Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 36 km/h brakes with a constant deceleration of 7 m/s² until it stops. Find the braking distance s.
v₀ = 36 km/ha = −7 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 1.9 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 1.9 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 13 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 13 kgθ = 25°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1.5 kg block on a ramp at 20° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 7 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1.5 kgm2 = 7 kgθ = 20°μ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 18 m/s and 60° above the horizontal towards a wall 17 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 18 m/sθ = 60°x = 17 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 31 m/sθ = 45°h = 5 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 5 kg ball hangs on a light string of length 2 m. It is pulled aside until the string makes 30° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 5 kgL = 2 mθ = 30°g = 9.81 m/s²
T = N
8.Work & energyHard
A 15 kg block starts from rest at the bottom of a 30° slope and is pulled up the slope by a constant force of 120 N parallel to the slope. The coefficient of kinetic friction is 0.2. Find the speed v of the block after it has moved 5 m up the slope.
A 3 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3 kgm2 = 3.5 kgv1 = 2 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 1400 kg car travelling east at 11 m/s collides with a 2000 kg car travelling north at 11 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1400 kgv1 = 11 m/s (E)m2 = 2000 kgv2 = 11 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 210 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 200 mm to 75 mm while rising 3 m. At section 1 the pressure is 150 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 400 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 400 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 1100 kJ of heat from a reservoir at 400 °C, produces 297 kJ of work and rejects the rest to a reservoir at 35 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 400 °CTL = 35 °CQH = 1100 kJW = 297 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with glycerol (n = 1.47) for every angle of incidence above 40°. Find the refractive index n1 of the block.
θc = 40°n2 = 1.47
n1 =
20.Waves, sound & opticsHard
Light of wavelength 550 nm falls at right angles on a grating with 300 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 300 mm⁻¹λ = 550 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: s = 7.143 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 10²/(2·7) = 7.143 m
Answer
s = 7.143 m
2.Kinematics
Answer: d = 16.81 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(1.9 − t₁)
4.905·t₁² + 343·t₁ − 651.7 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·651.7))/(2·4.905) = 1.851 s
Depth
d = ½·9.81·1.851² = 16.81 m
Answer
d = 16.81 m
3.Newton’s laws
Answer: a = 2.812 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 68.67 N
m₁·g·sin θ = 5.033 N
μ·m₁·g·cos θ = 1.383 N
Acceleration of the system
a = (68.67 − 5.033 − 1.383)/8.5 = 7.324 m/s²
Answer
a = 7.324 m/s²
5.Projectile motion
Answer: y = 11.94 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 18·cos 60° = 9 m/s
t = x/vx = 17/9 = 1.889 s
Height at that time
y = 15.59·1.889 − ½·9.81·1.889² = 11.94 m
Answer
y = 11.94 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: t = 4.686 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 31·cos 45° = 21.92 m/s
vy = v0·sin θ = 31·sin 45° = 21.92 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 21.92·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (21.92 + √(480.5 + 98.1))/9.81 = 4.686 s
Answer
t = 4.686 s
7.Work & energy
Answer: T = 62.19 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·2·(1 − cos 30°) = 5.257 m²/s²
Forces at the bottom
m·g = 5·9.81 = 49.05 N
T = mg + mv²/L = 49.05 + 5·5.257/2 = 62.19 N
Answer
T = 62.19 N
Check: T = mg(3 − 2cos θ) = 62.19 N.
8.Work & energy
Answer: v = 3.736 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 15·9.81 = 147.2 N
mg·sin θ = 73.57 N
μ·mg·cos θ = 25.49 N
Work–energy
½mv² = (120 − 99.06)·5 = 104.7 J
v = √(2·104.7/15) = 3.736 m/s
Answer
v = 3.736 m/s
9.Momentum & collisions
Answer: v′2 = 1.846 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 3.5)/(3 + 3.5)·2 = −0.1538 m/s
v′2 = 2·3/(3 + 3.5)·2 = 1.846 m/s
Answer
v′2 = 1.846 m/s
10.Momentum & collisions
Answer: v′ = 7.898 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 513.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(250/150)·(513.1/313.1) = 5.462 L
Answer
V2 = 5.462 L
17.Heat engines & refrigerators
Answer: ηmax = 57.94 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/673.1 = 57.94 %
Answer
ηmax = 57.94 %
18.Heat engines & refrigerators
Answer: Sgen = 0.9718 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 1100 − 297 = 803 kJ
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 35 + 273.15 = 308.1 K
Entropy changes of the reservoirs
ΔSH = −1100/673.1 = −1.634 kJ/K
ΔSL = 803/308.1 = 2.606 kJ/K
Sgen = 2.606 − 1.634 = 0.9718 kJ/K
Answer
Sgen = 0.9718 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: n1 = 2.287
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.47/0.6428 = 2.287
Answer
n1 = 2.287
20.Waves, sound & optics
Answer: θ2 = 19.27 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …