Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 10 m. At the same instant ball B is thrown straight up from the ground directly below at 21 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 10 mv0B = 21 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
A 30 kg box is pushed up a ramp at 35° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the pushing force F.
m = 30 kgθ = 35°μ = 0.25g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 7.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 7.5 kgm2 = 5.5 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 10 m/sθ = 20°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 25 m/sθ = 60°h = 20 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 14 m along the slope.
θ = 30°μ = 0.35d = 14 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 1 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.2) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 1 kgh = 2.5 mL = 5 mμ = 0.2k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1.5 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 1.5 kgm2 = 0.5 kgv1 = 2 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 29 m/s and bounces straight back at 17 m/s. The contact lasts 5 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.6 kgvin = 29 m/svout = 17 m/sΔt = 5 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 1 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a wind tunnel reads a difference of 300 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 300 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 50 mm and a gauge pressure of 30 kPa. The nozzle exit diameter is 25 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine receives heat from a source at 600 °C and rejects heat to the surroundings at 40 °C. Its actual thermal efficiency is 26%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 600 °CTL = 40 °Cη = 26%
ηII = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is -10 °C outside, delivering 8 kW of heat to the house. Find the highest possible coefficient of performance COPmax.
TH = 21 °CTL = -10 °CQ̇H = 8 kW
COPmax =
19.Waves, sound & opticsMedium
Light travels in water (n = 1.33) towards a flat boundary with air (n = 1.00). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.33n2 = 1.00
θc = °
20.Waves, sound & opticsHard
Light of wavelength 550 nm falls at right angles on a grating with 100 lines per millimetre. Find the angle θ3 of the order-3 maximum.
N = 100 mm⁻¹λ = 550 nmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: s = 69.44 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·4.5) = 69.44 m
Answer
s = 69.44 m
2.Kinematics
Answer: y = 8.888 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
10 − ½g·t² = 21·t − ½g·t² → t = 10/21 = 0.4762 s
Meeting height
y = 21·0.4762 − ½·9.81·0.4762² = 8.888 m
Answer
y = 8.888 m
3.Newton’s laws
Answer: F = 229.1 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 168.8 + 60.27 = 229.1 N
Answer
F = 229.1 N
4.Newton’s laws
Answer: T = 34.24 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 10·cos 20° = 9.397 m/s
vy = v0·sin θ = 10·sin 20° = 3.42 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 3.42²/(2·9.81) = 0.5962 m
Answer
H = 0.5962 m
6.Projectile motion
Answer: t = 5.198 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 25·cos 60° = 12.5 m/s
vy = v0·sin θ = 25·sin 60° = 21.65 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 21.65·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (21.65 + √(468.8 + 392.4))/9.81 = 5.198 s
Answer
t = 5.198 s
7.Work & energy
Answer: v = 7.354 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·14·(0.5 − 0.35·0.866)) = 7.354 m/s
Answer
v = 7.354 m/s
8.Work & energy
Answer: x = 7.672 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(2.5 − 0.2·5) = 14.71 J
Maximum compression
½kx² = 14.71 → x = √(2·14.71/5000) = 0.07672 m = 7.672 cm
Answer
x = 7.672 cm
9.Momentum & collisions
Answer: v′1 = 1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 0.5)/(1.5 + 0.5)·2 = 1 m/s
v′2 = 2·1.5/(1.5 + 0.5)·2 = 3 m/s
Answer
v′1 = 1 m/s
10.Momentum & collisions
Answer: J = 27.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(17 + 29) = 27.6 N·s
Answer
J = 27.6 N·s
11.Hydrostatic force
Answer: F = 44.15 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1/2 = 1.5 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·3 = 44.15 kN
Answer
F = 44.15 kN
12.Hydrostatic force
Answer: F = 90.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2·4.5 = 90.5 kN
Answer
F = 90.5 kN
13.Continuity & Bernoulli
Answer: v = 22.36 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·300/1.2) = 22.36 m/s
Answer
v = 22.36 m/s
14.Continuity & Bernoulli
Answer: H = 3.262 m
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 25/50 = 0.5
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·30000/(1000·0.9375)) = 8 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 8²/(2·9.81) = 3.262 m
Answer
H = 3.262 m
15.Ideal gas law
Answer: P = 598.9 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 160/32 = 5 mol
T = 15 + 273.15 = 288.1 K
Pressure
P = nRT/V = 5·8.314·288.1/0.02 = 598.9 kPa
Answer
P = 598.9 kPa
16.Ideal gas law
Answer: ρ = 2.298 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 20 + 273.15 = 293.1 K
Density
ρ = 200·28.01/(8.314·293.1) = 2.298 kg/m³
Answer
ρ = 2.298 kg/m³
17.Heat engines & refrigerators
Answer: ηII = 40.54 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηCarnot = 1 − 313.1/873.1 = 64.14 %
Second-law efficiency
ηII = η/ηCarnot = 26/64.14 = 40.54 %
Answer
ηII = 40.54 %
18.Heat engines & refrigerators
Answer: COPmax = 9.489
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.00/1.33 = 0.7519
Critical angle
θc = arcsin(0.7519) = 48.75°
Answer
θc = 48.75°
20.Waves, sound & optics
Answer: θ3 = 9.497 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …