Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
v₀ = 108 km/ha = −3 m/s²v = 0
t = s
2.KinematicsHard
Ball A is dropped from rest from a height of 45 m. At the same instant ball B is thrown straight up from the ground directly below at 21 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 45 mv0B = 21 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
A 2 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 2 kgθ = 45°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 5.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5.5 kgm2 = 3.5 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 70° above the horizontal and lands 55 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 70°R = 55 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 13 m/sθ = 55°h = 40 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 2.5 kg block slides 11 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 2.5 kgθ = 45°μ = 0.3d = 11 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 4 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.3) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 3.5 mL = 1 mμ = 0.3k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1100 kg car moving at 14 m/s runs into a stationary 1500 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1100 kgv1 = 14 m/sm2 = 1500 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 27 m/s and bounces straight back at 19 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.55 kgvin = 27 m/svout = 19 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 2 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows at 20 L/s through a horizontal pipe that narrows from 100 mm to 75 mm. The pressure in the narrow section is 270 kPa. Ignoring losses, find the pressure p1 in the wide section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 6 m. At section 1 the pressure is 240 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 575 °C and a cold reservoir at 15 °C. It takes in 2800 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 575 °CTL = 15 °CQH = 2800 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 120 kW of heat from a source at 550 °C and rejects heat to the surroundings at 25 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -5 °C and also rejects heat to the surroundings at 25 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 550 °CT0 = 25 °CTL = -5 °CQ̇H = 120 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A source of 600 Hz moving at 25 m/s and an observer moving at 15 m/s move away from each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 600 Hzv = 343 m/svs = 25 m/svo = 15 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 40 cm apart: lens 1 with f₁ = 8 cm and lens 2 with f₂ = −10 cm. An object stands 50 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 8 cmf2 = −10 cms = 40 cmdo = 50 cm
di2 = cm
3Solutions
1.Kinematics
Answer: t = 10 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 30/3 = 10 s
Answer
t = 10 s
2.Kinematics
Answer: y = 22.48 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
45 − ½g·t² = 21·t − ½g·t² → t = 45/21 = 2.143 s
Meeting height
y = 21·2.143 − ½·9.81·2.143² = 22.48 m
Answer
y = 22.48 m
3.Newton’s laws
Answer: a = 5.549 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·55/sin 140°) = 28.97 m/s
Answer
v0 = 28.97 m/s
6.Projectile motion
Answer: t = 4.141 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 13·cos 55° = 7.456 m/s
vy = v0·sin θ = 13·sin 55° = 10.65 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 10.65·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (10.65 + √(113.4 + 784.8))/9.81 = 4.141 s
Answer
t = 4.141 s
7.Work & energy
Answer: Wf = 57.23 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.7071 = 17.34 N
F = μN = 0.3·17.34 = 5.203 N
Work against friction
Wf = F·d = 5.203·11 = 57.23 J
Answer
Wf = 57.23 J
8.Work & energy
Answer: x = 40.92 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(3.5 − 0.3·1) = 125.6 J
Maximum compression
½kx² = 125.6 → x = √(2·125.6/1500) = 0.4092 m = 40.92 cm
Answer
x = 40.92 cm
9.Momentum & collisions
Answer: ΔK = 62192 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1100·14/2600 = 5.923 m/s
Kinetic energy before and after
Kbefore = ½·1100·14² = 107800 J
Kafter = ½·2600·5.923² = 45608 J
Energy lost
ΔK = 107800 − 45608 = 62192 J
Answer
ΔK = 62192 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 25.3 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(19 + 27) = 25.3 N·s
Answer
J = 25.3 N·s
11.Hydrostatic force
Answer: F = 134.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·5 = 134.9 kN
Answer
F = 134.9 kN
12.Hydrostatic force
Answer: ycp = 4.083 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·4·4 = 138.1 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·2³/12 = 1.333 m⁴
ycp = yc + Ic/(yc·A) = 4 + 1.333/(4·4) = 4.083 m
Answer
ycp = 4.083 m
13.Continuity & Bernoulli
Answer: p1 = 277 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 575 + 273.15 = 848.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/848.1 = 66.03 %
Maximum work
Wmax = ηmax·QH = 0.6603·2800 = 1849 kJ
Answer
Wmax = 1849 kJ
18.Heat engines & refrigerators
Answer: Q̇L = 684.1 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
T0 = 25 + 273.15 = 298.1 K
TL = -5 + 273.15 = 268.1 K
Engine work
η = 1 − 298.1/823.1 = 0.6378
Ẇ = 0.6378·120 = 76.54 kW
Heat removed by the refrigerator
COPR = 268.1/(298.1 − 268.1) = 8.938
Q̇L = 8.938·76.54 = 684.1 kW
Answer
Q̇L = 684.1 kW
19.Waves, sound & optics
Answer: f′ = 534.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.