Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 26 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 4.5 m/s². How long does it take the police car to catch up? Find t.
vcar = 26 m/sapolice = 4.5 m/s²v0,police = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 13 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 13 m/sh₀ = 35 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
An 18 kg block slides down a frictionless slope at 20° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 18 kgθ = 20°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 2 kgm2 = 1.5 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 24 m/sθ = 70°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 16 m/sθ = 50°h = 35 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 20 m along the slope.
θ = 35°μ = 0.15d = 20 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 5 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.1) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 3.5 mL = 2 mμ = 0.1k = 4000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 15 g bullet is fired horizontally into a 3 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 19 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 3 kgh = 19 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
At a crossing a 1500 kg car travelling east at 13 m/s collides with a 1400 kg car travelling north at 19 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1500 kgv1 = 13 m/s (E)m2 = 1400 kgv2 = 19 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 50 mm. The water level is kept 2.5 m above the orifice and the discharge coefficient is 0.63. Find the flow rate Q. Use g = 9.81 m/s².
d = 50 mmh = 2.5 mCd = 0.63g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 75 mm and a gauge pressure of 120 kPa. The nozzle exit diameter is 40 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine receives heat from a source at 850 °C and rejects heat to the surroundings at 30 °C. Its actual thermal efficiency is 37%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 850 °CTL = 30 °Cη = 37%
ηII = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 0 °C outside, delivering 13 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = 0 °CQ̇H = 13 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
Light travels in acrylic (n = 1.49) towards a flat boundary with air (n = 1.00). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.49n2 = 1.00
θc = °
20.Waves, sound & opticsHard
Light of wavelength 480 nm falls on two slits 0.3 mm apart. The screen is 1.2 m away. Find the distance y2 from the central bright fringe to bright fringe number 2.
λ = 480 nmd = 0.3 mmL = 1.2 mm = 2
y2 = mm
3Solutions
1.Kinematics
Answer: t = 11.56 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·26/4.5 = 11.56 s
Answer
t = 11.56 s
At that moment the police car moves at 2v = 52 m/s.
2.Kinematics
Answer: hmax = 43.61 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 13²/(2·9.81) = 8.614 m
Height above the ground
hmax = 35 + 8.614 = 43.61 m
Answer
hmax = 43.61 m
3.Newton’s laws
Answer: a = 3.355 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 70° = 8.208 m/s
vy = v0·sin θ = 24·sin 70° = 22.55 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·22.55/9.81 = 4.598 s
Horizontal distance
x = vx·t = 8.208·4.598 = 37.74 m
Answer
x = 37.74 m
6.Projectile motion
Answer: t = 4.198 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 50° = 10.28 m/s
vy = v0·sin θ = 16·sin 50° = 12.26 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 12.26·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (12.26 + √(150.2 + 686.7))/9.81 = 4.198 s
Answer
t = 4.198 s
7.Work & energy
Answer: v = 13.3 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·20·(0.5736 − 0.15·0.8192)) = 13.3 m/s
Answer
v = 13.3 m/s
8.Work & energy
Answer: x = 28.45 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(3.5 − 0.1·2) = 161.9 J
Maximum compression
½kx² = 161.9 → x = √(2·161.9/4000) = 0.2845 m = 28.45 cm
Answer
x = 28.45 cm
9.Momentum & collisions
Answer: v = 388.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.19) = 1.931 m/s
Collision
m·v = (m + M)·V → v = (0.015 + 3)·1.931/0.015 = 388.1 m/s
Answer
v = 388.1 m/s
10.Momentum & collisions
Answer: v′ = 11.37 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1/2 = 2.5 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·1.5 = 36.79 kN
Answer
F = 36.79 kN
12.Hydrostatic force
Answer: F = 56.56 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1.5/2 = 1.25 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.25·4.5 = 56.56 kN
Answer
F = 56.56 kN
13.Continuity & Bernoulli
Answer: Q = 8.663 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·2.5) = 7.004 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 40/75 = 0.5333
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·120000/(1000·0.9191)) = 16.16 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 16.16²/(2·9.81) = 13.31 m
Answer
H = 13.31 m
15.Ideal gas law
Answer: P = 432.5 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 60/16.04 = 3.741 mol
T = 5 + 273.15 = 278.1 K
Pressure
P = nRT/V = 3.741·8.314·278.1/0.02 = 432.5 kPa
Answer
P = 432.5 kPa
16.Ideal gas law
Answer: ρ = 12.15 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 10 + 273.15 = 283.1 K
Density
ρ = 650·44.01/(8.314·283.1) = 12.15 kg/m³
Answer
ρ = 12.15 kg/m³
17.Heat engines & refrigerators
Answer: ηII = 50.68 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 850 + 273.15 = 1123 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηCarnot = 1 − 303.1/1123 = 73.01 %
Second-law efficiency
ηII = η/ηCarnot = 37/73.01 = 50.68 %
Answer
ηII = 50.68 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.8869 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 13/14.66 = 0.8869 kW
Answer
Ẇmin = 0.8869 kW
19.Waves, sound & optics
Answer: θc = 42.16 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.00/1.49 = 0.6711
Critical angle
θc = arcsin(0.6711) = 42.16°
Answer
θc = 42.16°
20.Waves, sound & optics
Answer: y2 = 3.84 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …