Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 36 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
v₀ = 36 km/ha = −3 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 20 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 20 m/sh₀ = 40 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 16 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 16 kgθ = 30°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 9.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 9.5 kgm2 = 5 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 40 m/sθ = 65°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 24 m/s and 45° above the horizontal. It lands on the flat roof of a building 2 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 24 m/sθ = 45°hroof = 2 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 800 N/m. A 0.2 kg ball is placed on it and the spring is compressed by 10 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.2 kgk = 800 N/mx = 10 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 5 kg cart is released from rest at a height of 10.4 m on a smooth track that leads into a vertical circular loop of radius 4 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 5 kgh = 10.4 mR = 4 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 3.5 kg glider moving at 4 m/s makes a perfectly elastic head-on collision with a 3 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3.5 kgm2 = 3 kgv1 = 4 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
An 8 g bullet is fired horizontally into a 2 kg block hanging from light strings 0.9 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 2 kgL = 0.9 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 1.5 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 40 mm. In the wide section the pressure is 300 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 6 m. At section 1 the pressure is 330 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 3000 kJ of heat from a reservoir at 700 °C and rejects 981 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 700 °CQH = 3000 kJQL = 981 kJ
TL = °C
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1050 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 35 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 1050 °CTL = 35 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.6 m long; waves travel on it at 80 m/s. Find the frequency f5 of its harmonic number 5.
v = 80 m/sn = 5L = 0.6 m
f5 = Hz
20.Waves, sound & opticsHard
Light of wavelength 600 nm falls at right angles on a grating with 100 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 100 mm⁻¹λ = 600 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: t = 3.333 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 10/3 = 3.333 s
Answer
t = 3.333 s
2.Kinematics
Answer: t = 5.547 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−40 = 20·t − ½·9.81·t²
4.905·t² − 20·t − 40 = 0
Solve the quadratic
Only the positive root is physical.
t = (20 + √(20² + 2·9.81·40))/9.81 = 5.547 s
Answer
t = 5.547 s
3.Newton’s laws
Answer: a = 4.055 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 65° = 16.9 m/s
vy = v0·sin θ = 40·sin 65° = 36.25 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·36.25/9.81 = 7.391 s
Horizontal distance
x = vx·t = 16.9·7.391 = 124.9 m
Answer
x = 124.9 m
6.Projectile motion
Answer: x = 56.64 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 16.97 m/s, vy = 16.97 m/s
Time to land on the roof
Larger root: the ball is descending.
2 = 16.97·t − 4.905·t²
t = (16.97 + √(16.97² − 2·9.81·2))/9.81 = 3.338 s
Horizontal distance
x = vx·t = 16.97·3.338 = 56.64 m
Answer
x = 56.64 m
7.Work & energy
Answer: h = 2.039 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·800·0.1² = 4 J
Height
m·g = 0.2·9.81 = 1.962 N
h = ½kx²/(mg) = 4/1.962 = 2.039 m
Answer
h = 2.039 m
8.Work & energy
Answer: N = 9.81 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(10.4 − 8) = 47.09 m²/s²
Forces at the top
m·g = 5·9.81 = 49.05 N
N = mv²/R − mg = 5·47.09/4 − 49.05 = 9.81 N
Answer
N = 9.81 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′2 = 4.308 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 3)/(3.5 + 3)·4 = 0.3077 m/s
v′2 = 2·3.5/(3.5 + 3)·4 = 4.308 m/s
Answer
v′2 = 4.308 m/s
10.Momentum & collisions
Answer: v = 386.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.9·(1 − cos 30°) = 0.1206 m
Speed after impact
V = √(2·9.81·0.1206) = 1.538 m/s
Collision
v = (m + M)·V/m = 2.008·1.538/0.008 = 386.1 m/s
Answer
v = 386.1 m/s
11.Hydrostatic force
Answer: F = 9.81 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·1 = 9.81 kN
Answer
F = 9.81 kN
12.Hydrostatic force
Answer: ycp = 3.8 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.75·4.5 = 145.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 700 + 273.15 = 973.1 K
Reversible heat ratio
TL = TH·QL/QH = 973.1·981/3000 = 318.2 K = 45.07 °C
Answer
TL = 45.07 °C
18.Heat engines & refrigerators
Answer: Tm = 365.4 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1050 + 273.15 = 1323 K
TL = 35 + 273.15 = 308.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(1323·308.1) = 638.5 K = 365.4 °C
Answer
Tm = 365.4 °C
19.Waves, sound & optics
Answer: f5 = 333.3 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.6/5 = 0.24 m
Frequency
f = v/λ = 80/0.24 = 333.3 Hz
Answer
f5 = 333.3 Hz
20.Waves, sound & optics
Answer: θ1 = 3.44 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …