Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 36 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 36 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 9 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 9 m/sh₀ = 30 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 25 kg sled is pulled across level snow by a rope at 20° above the horizontal with a force of 60 N. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 25 kgF = 60 Nθ = 20°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 75 N pulls the front 7 kg block; the 1 kg block is towed behind. The coefficient of kinetic friction is 0.2 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 1 kgm2 = 7 kgF = 75 Nμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 26 m/sθ = 40°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 14 m/sθ = 40°h = 40 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.25. Find its speed v after it has slid 4 m along the slope.
θ = 20°μ = 0.25d = 4 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4.5 m long (μ = 0.3) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 5 mL = 4.5 mμ = 0.3k = 4000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2.5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2.5 kgm2 = 4 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 9 m/s and bounces straight back at 13 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
m = 0.5 kgvin = 9 m/svout = 13 m/sΔt = 25 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 1.5 mH = 1 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 150 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 170 kPa. Water leaves through an opening with a diameter of 20 mm, 2 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 750 °C and a cold reservoir at 30 °C. It takes in 3900 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 750 °CTL = 30 °CQH = 3900 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is -10 °C outside, delivering 14 kW of heat to the house. Find the highest possible coefficient of performance COPmax.
TH = 22 °CTL = -10 °CQ̇H = 14 kW
COPmax =
19.Waves, sound & opticsMedium
An object stands 18 cm in front of a thin converging lens with a focal length of 15 cm. Find the magnification m (negative for an inverted image).
do = 18 cmf = 15 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 550 nm falls on two slits 0.2 mm apart. The screen is 1.5 m away. Find the distance y4 from the central bright fringe to bright fringe number 4.
λ = 550 nmd = 0.2 mmL = 1.5 mm = 4
y4 = mm
3Solutions
1.Kinematics
Answer: s = 11.11 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 10²/(2·4.5) = 11.11 m
Answer
s = 11.11 m
2.Kinematics
Answer: hmax = 34.13 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 9²/(2·9.81) = 4.128 m
Height above the ground
hmax = 30 + 4.128 = 34.13 m
Answer
hmax = 34.13 m
3.Newton’s laws
Answer: a = 1.356 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 245.3 − 60·sin 20° = 224.7 N
Horizontal forces
m·a = F·cos θ − μ·N = 56.38 − 22.47
a = 33.91/25 = 1.356 m/s²
Answer
a = 1.356 m/s²
4.Newton’s laws
Answer: T = 9.375 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: x = 67.86 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 26·cos 40° = 19.92 m/s
vy = v0·sin θ = 26·sin 40° = 16.71 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·16.71/9.81 = 3.407 s
Horizontal distance
x = vx·t = 19.92·3.407 = 67.86 m
Answer
x = 67.86 m
6.Projectile motion
Answer: t = 3.917 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 40° = 10.72 m/s
vy = v0·sin θ = 14·sin 40° = 8.999 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 8.999·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (8.999 + √(80.98 + 784.8))/9.81 = 3.917 s
Answer
t = 3.917 s
7.Work & energy
Answer: v = 2.899 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·4·(0.342 − 0.25·0.9397)) = 2.899 m/s
Answer
v = 2.899 m/s
8.Work & energy
Answer: x = 18.92 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(5 − 0.3·4.5) = 71.61 J
Maximum compression
½kx² = 71.61 → x = √(2·71.61/4000) = 0.1892 m = 18.92 cm
Answer
x = 18.92 cm
9.Momentum & collisions
Answer: v′2 = 8.462 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2.5 − 4)/(2.5 + 4)·11 = −2.538 m/s
v′2 = 2·2.5/(2.5 + 4)·11 = 8.462 m/s
Answer
v′2 = 8.462 m/s
10.Momentum & collisions
Answer: Favg = 440 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(13 + 9) = 11 N·s
Average force
Favg = J/Δt = 11/0.025 = 440 N
Answer
Favg = 440 N
11.Hydrostatic force
Answer: F = 147.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·6 = 147.2 kN
Answer
F = 147.2 kN
12.Hydrostatic force
Answer: ycp = 2.042 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1/2 = 2 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2·2 = 34.53 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·1³/12 = 0.1667 m⁴
ycp = yc + Ic/(yc·A) = 2 + 0.1667/(2·2) = 2.042 m
Answer
ycp = 2.042 m
13.Continuity & Bernoulli
Answer: p2 = 144.5 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/1023 = 70.37 %
Maximum work
Wmax = ηmax·QH = 0.7037·3900 = 2744 kJ
Answer
Wmax = 2744 kJ
18.Heat engines & refrigerators
Answer: COPmax = 9.223
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/15 − 1/18
di = 90 cm
Magnification
m = −di/do = −90/18 = −5
Answer
m = −5
20.Waves, sound & optics
Answer: y4 = 16.5 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …