Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −7.5 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 9 s, then runs at constant speed for 28 s, and finally brakes at 2 m/s² until it stops. Find the total travel time t.
a1 = 1.5 m/s²t1 = 9 st2 = 28 sa3 = −2 m/s²
t = s
3.Newton’s lawsMedium
A 5 kg box is pushed up a ramp at 15° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the pushing force F.
m = 5 kgθ = 15°μ = 0.1g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 11 m/s. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 11 m/sθ = 30°μ = 0.3g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 40 m/sθ = 65°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 35° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 31 m/sθ = 35°h = 45 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 1000 N/m. A 0.15 kg ball is placed on it and the spring is compressed by 6 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.15 kgk = 1000 N/mx = 6 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 5 kg cart is released from rest at a height of 4.5 m on a smooth track that leads into a vertical circular loop of radius 1 m. Find the speed v of the cart at the top of the loop.
m = 5 kgh = 4.5 mR = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 4.5 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 2 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 4.5 kgm2 = 2 kgv1 = 5 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
An 8 g bullet is fired horizontally into a 4 kg block hanging from light strings 1.3 m long, and stays in it. The strings swing out to a largest angle of 25° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 4 kgL = 1.3 mθ = 25°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows at 23 L/s through a horizontal pipe that narrows from 150 mm to 100 mm. The pressure in the narrow section is 220 kPa. Ignoring losses, find the pressure p1 in the wide section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 6 m. At section 1 the pressure is 130 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 600 °C and rejects heat to the surroundings at 35 °C. Its actual thermal efficiency is 45%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 600 °CTL = 35 °Cη = 45%
ηII = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 1800 kJ of heat from a reservoir at 600 °C, produces 918 kJ of work and rejects the rest to a reservoir at 40 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 600 °CTL = 40 °CQH = 1800 kJW = 918 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with acrylic (n = 1.49) for every angle of incidence above 38°. Find the refractive index n1 of the block.
θc = 38°n2 = 1.49
n1 =
20.Waves, sound & opticsHard
Light of wavelength 405 nm falls at right angles on a grating with 800 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 800 mm⁻¹λ = 405 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: s = 60 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·7.5) = 60 m
Answer
s = 60 m
2.Kinematics
Answer: t = 43.75 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·9 = 13.5 m/s
Braking time
t3 = v/a3 = 13.5/2 = 6.75 s
Total time
t = 9 + 28 + 6.75 = 43.75 s
Answer
t = 43.75 s
3.Newton’s laws
Answer: F = 17.43 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 12.7 + 4.738 = 17.43 N
Answer
F = 17.43 N
4.Newton’s laws
Answer: d = 8.117 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.3·cos 30°) = 7.454 m/s²
Distance
d = v₀²/(2a) = 11²/(2·7.454) = 8.117 m
Answer
d = 8.117 m
5.Projectile motion
Answer: H = 66.98 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 65° = 16.9 m/s
vy = v0·sin θ = 40·sin 65° = 36.25 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 36.25²/(2·9.81) = 66.98 m
Answer
H = 66.98 m
6.Projectile motion
Answer: x = 135.7 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 31·cos 35° = 25.39 m/s
vy = v0·sin θ = 31·sin 35° = 17.78 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 17.78·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (17.78 + √(316.2 + 882.9))/9.81 = 5.342 s
Horizontal distance
x = vx·t = 25.39·5.342 = 135.7 m
Answer
x = 135.7 m
7.Work & energy
Answer: h = 1.223 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 6 cm = 0.06 m
½kx² = ½·1000·0.06² = 1.8 J
Height
m·g = 0.15·9.81 = 1.472 N
h = ½kx²/(mg) = 1.8/1.472 = 1.223 m
Answer
h = 1.223 m
8.Work & energy
Answer: v = 7.004 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(4.5 − 2) = 49.05 m²/s²
v = 7.004 m/s
Answer
v = 7.004 m/s
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′1 = 1.923 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4.5 − 2)/(4.5 + 2)·5 = 1.923 m/s
v′2 = 2·4.5/(4.5 + 2)·5 = 6.923 m/s
Answer
v′1 = 1.923 m/s
10.Momentum & collisions
Answer: v = 774.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.3·(1 − cos 25°) = 0.1218 m
Speed after impact
V = √(2·9.81·0.1218) = 1.546 m/s
Collision
v = (m + M)·V/m = 4.008·1.546/0.008 = 774.5 m/s
Answer
v = 774.5 m/s
11.Hydrostatic force
Answer: F = 239.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·7.5 = 239.1 kN
Answer
F = 239.1 kN
12.Hydrostatic force
Answer: F = 105.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2/2 = 3.5 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3.5·3 = 105.6 kN
Answer
F = 105.6 kN
13.Continuity & Bernoulli
Answer: p1 = 223.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηCarnot = 1 − 308.1/873.1 = 64.71 %
Second-law efficiency
ηII = η/ηCarnot = 45/64.71 = 69.54 %
Answer
ηII = 69.54 %
18.Heat engines & refrigerators
Answer: Sgen = 0.755 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 1800 − 918 = 882 kJ
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 40 + 273.15 = 313.1 K
Entropy changes of the reservoirs
ΔSH = −1800/873.1 = −2.062 kJ/K
ΔSL = 882/313.1 = 2.817 kJ/K
Sgen = 2.817 − 2.062 = 0.755 kJ/K
Answer
Sgen = 0.755 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: n1 = 2.42
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.49/0.6157 = 2.42
Answer
n1 = 2.42
20.Waves, sound & optics
Answer: θ2 = 40.39 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …