Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 120 km/h brakes with a constant deceleration of 4 m/s² until it stops. Find the braking distance s.
v₀ = 120 km/ha = −4 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 15 m. At the same instant ball B is thrown straight up from the ground directly below at 17 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 15 mv0B = 17 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 5.5 m/s and comes to rest after 7.7 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 5.5 m/sd = 7.7 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
An 8 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 0.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 8 kgm2 = 0.5 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 16 m/s and 30° above the horizontal towards a wall 18 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 16 m/sθ = 30°x = 18 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is thrown from ground level at 28 m/s and 70° above the horizontal. It lands on the flat roof of a building 14 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 28 m/sθ = 70°hroof = 14 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 2 kg block slides 6 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.25. Find the work Wf done against friction.
m = 2 kgθ = 20°μ = 0.25d = 6 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.3) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 3 mL = 3.5 mμ = 0.3k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 900 kg car moving at 9 m/s runs into a stationary 1400 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 900 kgv1 = 9 m/sm2 = 1400 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
At a crossing a 1400 kg car travelling east at 21 m/s collides with a 1600 kg car travelling north at 14 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1400 kgv1 = 21 m/s (E)m2 = 1600 kgv2 = 14 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 390 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 200 mm to 100 mm while rising 8 m. At section 1 the pressure is 260 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 650 °C and rejects heat to the surroundings at 35 °C. Its actual thermal efficiency is 37%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 650 °CTL = 35 °Cη = 37%
ηII = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1000 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 30 °C. Both engines produce the same work. Find Tm in °C.
TH = 1000 °CTL = 30 °C
Tm = °C
19.Waves, sound & opticsMedium
An observer moves at 10 m/s towards a stationary source of 800 Hz. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 800 Hzv = 343 m/svo = 10 m/s
f′ = Hz
20.Waves, sound & opticsHard
A diffraction grating has 300 lines per millimetre. Light of wavelength 600 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 300 mm⁻¹λ = 600 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 138.9 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 33.33²/(2·4) = 138.9 m
Answer
s = 138.9 m
2.Kinematics
Answer: t = 0.8824 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
15 − ½g·t² = 17·t − ½g·t² → t = 15/17 = 0.8824 s
Answer
t = 0.8824 s
3.Newton’s laws
Answer: μ = 0.2002
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 5.5²/(2·7.7) = 1.964 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.964/9.81 = 0.2002
Answer
μ = 0.2002
4.Newton’s laws
Answer: a = 0.5771 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 16·cos 30° = 13.86 m/s
t = x/vx = 18/13.86 = 1.299 s
Height at that time
y = 8·1.299 − ½·9.81·1.299² = 2.115 m
Answer
y = 2.115 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 45.63 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 9.577 m/s, vy = 26.31 m/s
Time to land on the roof
Larger root: the ball is descending.
14 = 26.31·t − 4.905·t²
t = (26.31 + √(26.31² − 2·9.81·14))/9.81 = 4.765 s
Horizontal distance
x = vx·t = 9.577·4.765 = 45.63 m
Answer
x = 45.63 m
7.Work & energy
Answer: Wf = 27.66 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 19.62·0.9397 = 18.44 N
F = μN = 0.25·18.44 = 4.609 N
Work against friction
Wf = F·d = 4.609·6 = 27.66 J
Answer
Wf = 27.66 J
8.Work & energy
Answer: x = 6.185 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(3 − 0.3·3.5) = 9.565 J
Maximum compression
½kx² = 9.565 → x = √(2·9.565/5000) = 0.06185 m = 6.185 cm
Answer
x = 6.185 cm
9.Momentum & collisions
Answer: ΔK = 22187 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 900·9/2300 = 3.522 m/s
Kinetic energy before and after
Kbefore = ½·900·9² = 36450 J
Kafter = ½·2300·3.522² = 14263 J
Energy lost
ΔK = 36450 − 14263 = 22187 J
Answer
ΔK = 22187 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v′ = 12.32 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: F = 30.17 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1/2 = 2 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2·1.5 = 30.17 kN
Answer
F = 30.17 kN
13.Continuity & Bernoulli
Answer: p2 = 388.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηCarnot = 1 − 308.1/923.1 = 66.62 %
Second-law efficiency
ηII = η/ηCarnot = 37/66.62 = 55.54 %
Answer
ηII = 55.54 %
18.Heat engines & refrigerators
Answer: Tm = 515 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1000 + 273.15 = 1273 K
TL = 30 + 273.15 = 303.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1273 + 303.1)/2 = 788.2 K = 515 °C
Answer
Tm = 515 °C
19.Waves, sound & optics
Answer: f′ = 823.3 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …