Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 34 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 6 m/s². How long does it take the police car to catch up? Find t.
vcar = 34 m/sapolice = 6 m/s²v0,police = 0
t = s
2.KinematicsHard
Ball A is dropped from rest from a height of 15 m. At the same instant ball B is thrown straight up from the ground directly below at 15 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 15 mv0B = 15 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
A 25 kg sled is pulled across level snow by a rope at 40° above the horizontal with a force of 90 N. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 25 kgF = 90 Nθ = 40°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 6.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 6.5 kgm2 = 2.5 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 32 m/s and must land 65 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 32 m/sR = 65 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 30 m/sθ = 55°h = 20 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.1. Find its speed v after it has slid 15 m along the slope.
θ = 25°μ = 0.1d = 15 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 3 kg block rests on a rough horizontal table (μ = 0.15). A light string runs from it over a smooth pulley at the edge of the table to a hanging 4 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
m1 = 3 kgm2 = 4 kgμ = 0.15d = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 500 kg car moving at 16 m/s runs into a stationary 1500 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 500 kgv1 = 16 m/sm2 = 1500 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 1500 kg car runs into a parked 1100 kg car. The wrecks lock together and skid 6.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.5. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 230 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 1 m. At section 1 the pressure is 320 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 625 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 625 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 4800 kJ of heat from a reservoir at 400 °C, produces 1968 kJ of work and rejects the rest to a reservoir at 10 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 400 °CTL = 10 °CQH = 4800 kJW = 1968 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A source of 800 Hz moving at 20 m/s and an observer moving at 15 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 800 Hzv = 343 m/svs = 20 m/svo = 15 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 60 cm apart: lens 1 with f₁ = 8 cm and lens 2 with f₂ = 15 cm. An object stands 40 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 8 cmf2 = 15 cms = 60 cmdo = 40 cm
di2 = cm
3Solutions
1.Kinematics
Answer: t = 11.33 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·34/6 = 11.33 s
Answer
t = 11.33 s
At that moment the police car moves at 2v = 68 m/s.
2.Kinematics
Answer: y = 10.09 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
15 − ½g·t² = 15·t − ½g·t² → t = 15/15 = 1 s
Meeting height
y = 15·1 − ½·9.81·1² = 10.09 m
Answer
y = 10.09 m
3.Newton’s laws
Answer: a = 2.008 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 245.3 − 90·sin 40° = 187.4 N
Horizontal forces
m·a = F·cos θ − μ·N = 68.94 − 18.74
a = 50.2/25 = 2.008 m/s²
Answer
a = 2.008 m/s²
4.Newton’s laws
Answer: a = 1.308 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·65/32² = 0.6227
Angle
2θ = 38.51° → θ = 19.26°
Answer
θ = 19.26°
The other solution is 90° − θ = 70.74°.
6.Projectile motion
Answer: x = 98.47 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 55° = 17.21 m/s
vy = v0·sin θ = 30·sin 55° = 24.57 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 24.57·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (24.57 + √(603.9 + 392.4))/9.81 = 5.723 s
Horizontal distance
x = vx·t = 17.21·5.723 = 98.47 m
Answer
x = 98.47 m
7.Work & energy
Answer: v = 9.885 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·15·(0.4226 − 0.1·0.9063)) = 9.885 m/s
Answer
v = 9.885 m/s
8.Work & energy
Answer: v = 3.154 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 39.24·1 = 39.24 J
μ·m₁g·d = 0.15·29.43·1 = 4.414 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 34.83 → v = √(2·34.83/7) = 3.154 m/s
Answer
v = 3.154 m/s
9.Momentum & collisions
Answer: ΔK = 48000 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 500·16/2000 = 4 m/s
Kinetic energy before and after
Kbefore = ½·500·16² = 64000 J
Kafter = ½·2000·4² = 16000 J
Energy lost
ΔK = 64000 − 16000 = 48000 J
Answer
ΔK = 48000 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v1 = 13.84 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·7.5 = 128.8 kN
Answer
F = 128.8 kN
12.Hydrostatic force
Answer: F = 45.25 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3·1.5 = 45.25 kN
Answer
F = 45.25 kN
13.Continuity & Bernoulli
Answer: p2 = 225.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 625 + 273.15 = 898.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/898.1 = 68.47 %
Answer
ηmax = 68.47 %
18.Heat engines & refrigerators
Answer: Sgen = 2.871 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 4800 − 1968 = 2832 kJ
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 10 + 273.15 = 283.1 K
Entropy changes of the reservoirs
ΔSH = −4800/673.1 = −7.131 kJ/K
ΔSL = 2832/283.1 = 10 kJ/K
Sgen = 10 − 7.131 = 2.871 kJ/K
Answer
Sgen = 2.871 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f′ = 886.7 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.