Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 5 s, then runs at constant speed for 25 s, and finally brakes at 4.5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 3 m/s²t1 = 5 st2 = 25 sa3 = −4.5 m/s²
s = m
3.Newton’s lawsMedium
A 30 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 140 N. The coefficient of kinetic friction is 0.4. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 30 kgF = 140 Nθ = 35°μ = 0.4g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 35° with a speed of 8.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 8.5 m/sθ = 35°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 20 m/sθ = 70°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 20 m/sθ = 40°h = 40 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 5 m along the slope.
θ = 25°μ = 0.15d = 5 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 5 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.2) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 1 mL = 1 mμ = 0.2k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2 kg glider moving at 12 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 1 kgv1 = 12 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 20 m/s and bounces straight back at 4 m/s. The contact lasts 25 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.55 kgvin = 20 m/svout = 4 m/sΔt = 25 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 4 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 100 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 6 m. At section 1 the pressure is 100 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 5 °C by removing 4.5 kW of heat, and rejects heat to the surroundings at 20 °C. Find the rate Q̇H at which it rejects heat.
TL = 5 °CTH = 20 °CQ̇L = 4.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is -5 °C outside, delivering 11 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = -5 °CQ̇H = 11 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 6 cm in front of a thin diverging lens with a focal length of 20 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 6 cmf = −20 cm
di = cm
20.Waves, sound & opticsHard
Two thin lenses share an axis, 60 cm apart: lens 1 with f₁ = 8 cm and lens 2 with f₂ = 10 cm. An object stands 50 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 8 cmf2 = 10 cms = 60 cmdo = 50 cm
di2 = cm
3Solutions
1.Kinematics
Answer: s = 75 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·6) = 75 m
Answer
s = 75 m
2.Kinematics
Answer: s = 437.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·5 = 15 m/s
Distance of each phase
s1 = ½·3·5² = 37.5 m
s2 = 15·25 = 375 m
s3 = 15²/(2·4.5) = 25 m
Total distance
s = 37.5 + 375 + 25 = 437.5 m
Answer
s = 437.5 m
3.Newton’s laws
Answer: a = 0.9694 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 294.3 − 140·sin 35° = 214 N
Horizontal forces
m·a = F·cos θ − μ·N = 114.7 − 85.6
a = 29.08/30 = 0.9694 m/s²
Answer
a = 0.9694 m/s²
4.Newton’s laws
Answer: d = 5.287 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 35° + 0.15·cos 35°) = 6.832 m/s²
Distance
d = v₀²/(2a) = 8.5²/(2·6.832) = 5.287 m
Answer
d = 5.287 m
5.Projectile motion
Answer: H = 18 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 70° = 6.84 m/s
vy = v0·sin θ = 20·sin 70° = 18.79 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 18.79²/(2·9.81) = 18 m
Answer
H = 18 m
6.Projectile motion
Answer: x = 68.22 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 40° = 15.32 m/s
vy = v0·sin θ = 20·sin 40° = 12.86 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 12.86·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (12.86 + √(165.3 + 784.8))/9.81 = 4.452 s
Horizontal distance
x = vx·t = 15.32·4.452 = 68.22 m
Answer
x = 68.22 m
7.Work & energy
Answer: v = 5.303 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·5·(0.4226 − 0.15·0.9063)) = 5.303 m/s
Answer
v = 5.303 m/s
8.Work & energy
Answer: x = 39.62 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(1 − 0.2·1) = 39.24 J
Maximum compression
½kx² = 39.24 → x = √(2·39.24/500) = 0.3962 m = 39.62 cm
Answer
x = 39.62 cm
9.Momentum & collisions
Answer: v′1 = 4 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 1)/(2 + 1)·12 = 4 m/s
v′2 = 2·2/(2 + 1)·12 = 16 m/s
Answer
v′1 = 4 m/s
10.Momentum & collisions
Answer: J = 13.2 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(4 + 20) = 13.2 N·s
Answer
J = 13.2 N·s
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: ycp = 5.636 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·6 = 323.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 20 + 273.15 = 293.1 K
TL = 5 + 273.15 = 278.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 4.5·293.1/278.1 = 4.743 kW
Answer
Q̇H = 4.743 kW
Power input: Ẇ = 0.2427 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 1.006 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 11/10.93 = 1.006 kW
Answer
Ẇmin = 1.006 kW
19.Waves, sound & optics
Answer: di = −4.615 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−20) − 1/6
di = −4.615 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −4.615 cm
20.Waves, sound & optics
Answer: di2 = 12.47 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.