Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 54 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
v₀ = 54 km/ha = −3 m/s²v = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 1 m/s² for 12 s, then runs at constant speed for 7 s, and finally brakes at 3 m/s² until it stops. Find the total distance s between the two stops.
a1 = 1 m/s²t1 = 12 st2 = 7 sa3 = −3 m/s²
s = m
3.Newton’s lawsMedium
A 40 kg box is pushed up a ramp at 30° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the pushing force F.
m = 40 kgθ = 30°μ = 0.15g = 9.81 m/s²
F = N
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 35 N pulls the front 7 kg block; the 1 kg block is towed behind. The coefficient of kinetic friction is 0.1 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 1 kgm2 = 7 kgF = 35 Nμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 60° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 34 m/sθ = 60°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 14 m/sθ = 30°h = 5 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 5 kg ball hangs on a light string of length 1 m. It is pulled aside until the string makes 40° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 5 kgL = 1 mθ = 40°g = 9.81 m/s²
T = N
8.Work & energyHard
A 2.5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.15) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 4 mL = 1.5 mμ = 0.15k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 900 kg car moving at 18 m/s runs into a stationary 800 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 900 kgv1 = 18 m/sm2 = 800 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.35 kg ball hits a wall at 19 m/s and bounces straight back at 13 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.35 kgvin = 19 m/svout = 13 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 220 kPa and the velocity is 2.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 200 mm to 50 mm while rising 9 m. At section 1 the pressure is 230 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 275 °C and a cold reservoir at 25 °C. Find the highest possible thermal efficiency ηmax.
TH = 275 °CTL = 25 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 160 kW of heat from a source at 500 °C and rejects heat to the surroundings at 30 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -30 °C and also rejects heat to the surroundings at 30 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 500 °CT0 = 30 °CTL = -30 °CQ̇H = 160 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A pipe open at both ends must have its harmonic number 5 at 572 Hz. The speed of sound is 343 m/s. Find the length L of the pipe.
v = 343 m/sn = 5f5 = 572 Hz
L = m
20.Waves, sound & opticsHard
A sensor at rest sends ultrasound of 35 kHz towards a car that moves away at 20 m/s and mixes the echo with the emitted signal. Find the beat frequency fb (speed of sound 343 m/s).
f = 35 kHzu = 20 m/sv = 343 m/s
fb = Hz
3Solutions
1.Kinematics
Answer: t = 5 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 54/3.6 = 15 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 15/3 = 5 s
Answer
t = 5 s
2.Kinematics
Answer: s = 180 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1·12 = 12 m/s
Distance of each phase
s1 = ½·1·12² = 72 m
s2 = 12·7 = 84 m
s3 = 12²/(2·3) = 24 m
Total distance
s = 72 + 84 + 24 = 180 m
Answer
s = 180 m
3.Newton’s laws
Answer: F = 247.2 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 196.2 + 50.97 = 247.2 N
Answer
F = 247.2 N
4.Newton’s laws
Answer: T = 4.375 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: H = 44.19 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 60° = 17 m/s
vy = v0·sin θ = 34·sin 60° = 29.44 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 29.44²/(2·9.81) = 44.19 m
Answer
H = 44.19 m
6.Projectile motion
Answer: t = 1.95 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 30° = 12.12 m/s
vy = v0·sin θ = 14·sin 30° = 7 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 7·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (7 + √(49 + 98.1))/9.81 = 1.95 s
Answer
t = 1.95 s
7.Work & energy
Answer: T = 72 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·1·(1 − cos 40°) = 4.59 m²/s²
Forces at the bottom
m·g = 5·9.81 = 49.05 N
T = mg + mv²/L = 49.05 + 5·4.59/1 = 72 N
Answer
T = 72 N
Check: T = mg(3 − 2cos θ) = 72 N.
8.Work & energy
Answer: x = 60.85 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(4 − 0.15·1.5) = 92.58 J
Maximum compression
½kx² = 92.58 → x = √(2·92.58/500) = 0.6085 m = 60.85 cm
Answer
x = 60.85 cm
9.Momentum & collisions
Answer: ΔK = 68612 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 900·18/1700 = 9.529 m/s
Kinetic energy before and after
Kbefore = ½·900·18² = 145800 J
Kafter = ½·1700·9.529² = 77188 J
Energy lost
ΔK = 145800 − 77188 = 68612 J
Answer
ΔK = 68612 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 1120 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.35·(13 + 19) = 11.2 N·s
Average force
Favg = J/Δt = 11.2/0.01 = 1120 N
Answer
Favg = 1120 N
11.Hydrostatic force
Answer: F = 104.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1.5/2 = 4.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.75·2.25 = 104.8 kN
Answer
F = 104.8 kN
12.Hydrostatic force
Answer: F = 82.96 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.75·3 = 82.96 kN
Answer
F = 82.96 kN
13.Continuity & Bernoulli
Answer: p2 = 184.5 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(250/500)·(443.1/283.1) = 3.913 L
Answer
V2 = 3.913 L
17.Heat engines & refrigerators
Answer: ηmax = 45.61 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 275 + 273.15 = 548.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/548.1 = 45.61 %
Answer
ηmax = 45.61 %
18.Heat engines & refrigerators
Answer: Q̇L = 394.2 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
T0 = 30 + 273.15 = 303.1 K
TL = -30 + 273.15 = 243.1 K
Engine work
η = 1 − 303.1/773.1 = 0.6079
Ẇ = 0.6079·160 = 97.26 kW
Heat removed by the refrigerator
COPR = 243.1/(303.1 − 243.1) = 4.052
Q̇L = 4.052·97.26 = 394.2 kW
Answer
Q̇L = 394.2 kW
19.Waves, sound & optics
Answer: L = 1.499 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 343/572 = 0.5997 m
Length
L = nλ/2 = 5·0.5997/2 = 1.499 m
Answer
L = 1.499 m
20.Waves, sound & optics
Answer: fb = 3857 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.