Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 80 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 80 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 11 s, then runs at constant speed for 8 s, and finally brakes at 3 m/s² until it stops. Find the total distance s between the two stops.
a1 = 3 m/s²t1 = 11 st2 = 8 sa3 = −3 m/s²
s = m
3.Newton’s lawsMedium
A 20 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 20 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 8 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 8 m/sθ = 20°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 28 m/sθ = 55°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 17 m/s and 60° above the horizontal from the top of a 35 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 17 m/sθ = 60°h = 35 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A car travelling at 110 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 110 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 10 kg block starts from rest at the bottom of a 25° slope and is pulled up the slope by a constant force of 75 N parallel to the slope. The coefficient of kinetic friction is 0.2. Find the speed v of the block after it has moved 6 m up the slope.
A 1100 kg car moving at 25 m/s runs into a stationary 1900 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1100 kgv1 = 25 m/sm2 = 1900 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
At a crossing a 1800 kg car travelling east at 16 m/s collides with a 1800 kg car travelling north at 15 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1800 kgv1 = 16 m/s (E)m2 = 1800 kgv2 = 15 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 2.5 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows at 11 L/s through a horizontal pipe that narrows from 150 mm to 100 mm. The pressure in the narrow section is 50 kPa. Ignoring losses, find the pressure p1 in the wide section.
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 1 m. At section 1 the pressure is 230 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 575 °C and a cold reservoir at 10 °C. It takes in 1700 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 575 °CTL = 10 °CQH = 1700 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 600 kJ of heat from a reservoir at 400 °C, produces 276 kJ of work and rejects the rest to a reservoir at 10 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 400 °CTL = 10 °CQH = 600 kJW = 276 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object stands 60 cm in front of a thin converging lens with a focal length of 5 cm. Find the magnification m (negative for an inverted image).
do = 60 cmf = 5 cm
m =
20.Waves, sound & opticsHard
An object is 40 cm in front of a convex mirror with a radius of curvature of 40 cm. Find the magnification m (negative for an inverted image).
do = 40 cmR = 40 cm
m =
3Solutions
1.Kinematics
Answer: s = 82.3 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 22.22²/(2·3) = 82.3 m
Answer
s = 82.3 m
2.Kinematics
Answer: s = 627 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·11 = 33 m/s
Distance of each phase
s1 = ½·3·11² = 181.5 m
s2 = 33·8 = 264 m
s3 = 33²/(2·3) = 181.5 m
Total distance
s = 181.5 + 264 + 181.5 = 627 m
Answer
s = 627 m
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 20° + 0.1·cos 20°) = 4.277 m/s²
Distance
d = v₀²/(2a) = 8²/(2·4.277) = 7.482 m
Answer
d = 7.482 m
5.Projectile motion
Answer: H = 26.81 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 55° = 16.06 m/s
vy = v0·sin θ = 28·sin 55° = 22.94 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 22.94²/(2·9.81) = 26.81 m
Answer
H = 26.81 m
6.Projectile motion
Answer: H = 46.05 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 17·sin 60° = 14.72 m/s
Rise above the cliff
Δh = vy²/(2g) = 14.72²/(2·9.81) = 11.05 m
Height above the ground
H = 35 + 11.05 = 46.05 m
Answer
H = 46.05 m
7.Work & energy
Answer: d = 67.98 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 110/3.6 = 30.56 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 30.56²/(2·0.7·9.81) = 67.98 m
Answer
d = 67.98 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 4.349 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 10·9.81 = 98.1 N
mg·sin θ = 41.46 N
μ·mg·cos θ = 17.78 N
Work–energy
½mv² = (75 − 59.24)·6 = 94.56 J
v = √(2·94.56/10) = 4.349 m/s
Answer
v = 4.349 m/s
9.Momentum & collisions
Answer: ΔK = 217708 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1100·25/3000 = 9.167 m/s
Kinetic energy before and after
Kbefore = ½·1100·25² = 343750 J
Kafter = ½·3000·9.167² = 126042 J
Energy lost
ΔK = 343750 − 126042 = 217708 J
Answer
ΔK = 217708 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v′ = 10.97 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·7.5 = 202.3 kN
Answer
F = 202.3 kN
12.Hydrostatic force
Answer: F = 183.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·4.25·5 = 183.4 kN
Answer
F = 183.4 kN
13.Continuity & Bernoulli
Answer: p1 = 50.79 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 575 + 273.15 = 848.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/848.1 = 66.62 %
Maximum work
Wmax = ηmax·QH = 0.6662·1700 = 1132 kJ
Answer
Wmax = 1132 kJ
18.Heat engines & refrigerators
Answer: Sgen = 0.2529 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 600 − 276 = 324 kJ
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 10 + 273.15 = 283.1 K
Entropy changes of the reservoirs
ΔSH = −600/673.1 = −0.8913 kJ/K
ΔSL = 324/283.1 = 1.144 kJ/K
Sgen = 1.144 − 0.8913 = 0.2529 kJ/K
Answer
Sgen = 0.2529 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: m = −0.09091
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/5 − 1/60
di = 5.455 cm
Magnification
m = −di/do = −5.455/60 = −0.09091
Answer
m = −0.09091
20.Waves, sound & optics
Answer: m = 0.3333
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.