Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 50 km/h sees an obstacle. Her reaction time is 1.3 s, after which the car brakes with a constant deceleration of 6.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 50 km/htr = 1.3 sa = −6.5 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 18 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 18 m/sh₀ = 25 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 35 kg sled is pulled across level snow by a rope at 20° above the horizontal with a force of 130 N. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 35 kgF = 130 Nθ = 20°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 15° with a speed of 8 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 8 m/sθ = 15°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 20° above the horizontal and lands 45 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 20°R = 45 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 55 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 13 m/sθ = 45°h = 55 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 8 m along the slope.
θ = 25°μ = 0.15d = 8 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg cart is released from rest at a height of 10 m on a smooth track that leads into a vertical circular loop of radius 2.5 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 2 kgh = 10 mR = 2.5 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 1500 kg car moving at 12 m/s runs into a stationary 900 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1500 kgv1 = 12 m/sm2 = 900 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 900 kg car runs into a parked 1600 kg car. The wrecks lock together and skid 11 m before stopping. The coefficient of kinetic friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 25 mm. The water level is kept 1.5 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².
d = 25 mmh = 1.5 mCd = 0.64g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A hose with an inner diameter of 32 mm siphons water from an open tank. The highest point C of the hose is 0.5 m above the water surface, and the outlet (open to the air) is 1 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A heat engine works between a hot reservoir at 350 °C and a cold reservoir at 30 °C. It takes in 4000 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 350 °CTL = 30 °CQH = 4000 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 7 °C outside, delivering 6 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = 7 °CQ̇H = 6 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
One machine gives a sound level of 75 dB at a certain point. Find the level β at that point when 4 identical machines run at the same time (incoherent sources).
β1 = 75 dBn = 4
β = dB
20.Waves, sound & opticsHard
Light of wavelength 500 nm falls on two slits 0.2 mm apart. The screen is 1.5 m away. Find the distance y1 from the central bright fringe to bright fringe number 1.
λ = 500 nmd = 0.2 mmL = 1.5 mm = 1
y1 = mm
3Solutions
1.Kinematics
Answer: d = 32.89 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Reaction distance
d1 = v₀·tr = 13.89·1.3 = 18.06 m
Braking distance
d2 = v₀²/(2a) = 13.89²/(2·6.5) = 14.84 m
Total
d = 18.06 + 14.84 = 32.89 m
Answer
d = 32.89 m
2.Kinematics
Answer: t = 4.744 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−25 = 18·t − ½·9.81·t²
4.905·t² − 18·t − 25 = 0
Solve the quadratic
Only the positive root is physical.
t = (18 + √(18² + 2·9.81·25))/9.81 = 4.744 s
Answer
t = 4.744 s
3.Newton’s laws
Answer: a = 1.355 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 343.4 − 130·sin 20° = 298.9 N
Horizontal forces
m·a = F·cos θ − μ·N = 122.2 − 74.72
a = 47.44/35 = 1.355 m/s²
Answer
a = 1.355 m/s²
4.Newton’s laws
Answer: d = 8.08 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 15° + 0.15·cos 15°) = 3.96 m/s²
Distance
d = v₀²/(2a) = 8²/(2·3.96) = 8.08 m
Answer
d = 8.08 m
5.Projectile motion
Answer: v0 = 26.21 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·45/sin 40°) = 26.21 m/s
Answer
v0 = 26.21 m/s
6.Projectile motion
Answer: t = 4.414 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 13·cos 45° = 9.192 m/s
vy = v0·sin θ = 13·sin 45° = 9.192 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 55 + 9.192·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9.192 + √(84.5 + 1079))/9.81 = 4.414 s
Answer
t = 4.414 s
7.Work & energy
Answer: v = 6.708 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·8·(0.4226 − 0.15·0.9063)) = 6.708 m/s
Answer
v = 6.708 m/s
8.Work & energy
Answer: N = 58.86 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(10 − 5) = 98.1 m²/s²
Forces at the top
m·g = 2·9.81 = 19.62 N
N = mv²/R − mg = 2·98.1/2.5 − 19.62 = 58.86 N
Answer
N = 58.86 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: ΔK = 40500 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1500·12/2400 = 7.5 m/s
Kinetic energy before and after
Kbefore = ½·1500·12² = 108000 J
Kafter = ½·2400·7.5² = 67500 J
Energy lost
ΔK = 108000 − 67500 = 40500 J
Answer
ΔK = 40500 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v1 = 36.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·1.5) = 5.425 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: P = 549.1 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 90/16.04 = 5.611 mol
T = 80 + 273.15 = 353.1 K
Pressure
P = nRT/V = 5.611·8.314·353.1/0.03 = 549.1 kPa
Answer
P = 549.1 kPa
16.Ideal gas law
Answer: ρ = 0.5288 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 0 + 273.15 = 273.1 K
Density
ρ = 300·4.003/(8.314·273.1) = 0.5288 kg/m³
Answer
ρ = 0.5288 kg/m³
17.Heat engines & refrigerators
Answer: Wmax = 2054 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 350 + 273.15 = 623.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/623.1 = 51.35 %
Maximum work
Wmax = ηmax·QH = 0.5135·4000 = 2054 kJ
Answer
Wmax = 2054 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.2661 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 6/22.55 = 0.2661 kW
Answer
Ẇmin = 0.2661 kW
19.Waves, sound & optics
Answer: β = 81.02 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Total intensity
I = 4·I₁
Level
β = 75 + 10·log₁₀(4) = 81.02 dB
Answer
β = 81.02 dB
20.Waves, sound & optics
Answer: y1 = 3.75 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …