Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 120 km/h sees an obstacle. Her reaction time is 1.2 s, after which the car brakes with a constant deceleration of 4.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 120 km/htr = 1.2 sa = −4.5 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 12 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 12 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 10 kg block slides down a frictionless slope at 30° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 10 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 6 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 6 kgm2 = 4 kgμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 60° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 10 m/sθ = 60°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 55 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 20 m/sθ = 45°h = 55 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.25. Find its speed v after it has slid 8 m along the slope.
θ = 35°μ = 0.25d = 8 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 5 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.3) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 5 kgh = 4.5 mL = 2.5 mμ = 0.3k = 1500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 2.5 kg glider moving at 8 m/s makes a perfectly elastic head-on collision with a 3 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2.5 kgm2 = 3 kgv1 = 8 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 9 m/s and bounces straight back at 15 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.2 kgvin = 9 m/svout = 15 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2.5 mH = 1 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
A pitot-static tube in a water pipe reads a difference of 36 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 36 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
A hose with an inner diameter of 25 mm siphons water from an open tank. The highest point C of the hose is 2 m above the water surface, and the outlet (open to the air) is 4.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 25 mmzC = +2 mz2 = −4.5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 330 g of CH₄ occupy at 600 kPa and 95 °C? Treat it as an ideal gas.
A heat engine works between a hot reservoir at 675 °C and a cold reservoir at 20 °C. Find the highest possible thermal efficiency ηmax.
TH = 675 °CTL = 20 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 110 kW of heat from a source at 500 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -30 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 500 °CT0 = 20 °CTL = -30 °CQ̇H = 110 kW
Q̇L = kW
19.Waves, sound & opticsMedium
One machine gives a sound level of 70 dB at a certain point. Find the level β at that point when 10 identical machines run at the same time (incoherent sources).
β1 = 70 dBn = 10
β = dB
20.Waves, sound & opticsHard
Light of wavelength 589 nm falls at right angles on a grating with 800 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 800 mm⁻¹λ = 589 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: d = 163.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Reaction distance
d1 = v₀·tr = 33.33·1.2 = 40 m
Braking distance
d2 = v₀²/(2a) = 33.33²/(2·4.5) = 123.5 m
Total
d = 40 + 123.5 = 163.5 m
Answer
d = 163.5 m
2.Kinematics
Answer: t = 3.584 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 12·t − ½·9.81·t²
4.905·t² − 12·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (12 + √(12² + 2·9.81·20))/9.81 = 3.584 s
Answer
t = 3.584 s
3.Newton’s laws
Answer: a = 4.905 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 10·cos 60° = 5 m/s
vy = v0·sin θ = 10·sin 60° = 8.66 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·8.66/9.81 = 1.766 s
Answer
t = 1.766 s
6.Projectile motion
Answer: t = 5.087 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 45° = 14.14 m/s
vy = v0·sin θ = 20·sin 45° = 14.14 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 55 + 14.14·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (14.14 + √(200 + 1079))/9.81 = 5.087 s
Answer
t = 5.087 s
7.Work & energy
Answer: v = 7.608 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·8·(0.5736 − 0.25·0.8192)) = 7.608 m/s
Answer
v = 7.608 m/s
8.Work & energy
Answer: v = 8.578 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(4.5 − 0.3·2.5) = 183.9 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.75) = 8.578 m/s
Answer
v = 8.578 m/s
9.Momentum & collisions
Answer: v′2 = 7.273 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2.5 − 3)/(2.5 + 3)·8 = −0.7273 m/s
v′2 = 2·2.5/(2.5 + 3)·8 = 7.273 m/s
Answer
v′2 = 7.273 m/s
10.Momentum & collisions
Answer: J = 4.8 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(15 + 9) = 4.8 N·s
Answer
J = 4.8 N·s
11.Hydrostatic force
Answer: F = 64.38 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·3.75 = 64.38 kN
Answer
F = 64.38 kN
12.Hydrostatic force
Answer: F = 25.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3·1 = 25.9 kN
Answer
F = 25.9 kN
13.Continuity & Bernoulli
Answer: v = 8.485 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·36000/1000) = 8.485 m/s
Answer
v = 8.485 m/s
14.Continuity & Bernoulli
Answer: Q = 4.612 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 675 + 273.15 = 948.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 293.1/948.1 = 69.08 %
Answer
ηmax = 69.08 %
18.Heat engines & refrigerators
Answer: Q̇L = 332.1 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
T0 = 20 + 273.15 = 293.1 K
TL = -30 + 273.15 = 243.1 K
Engine work
η = 1 − 293.1/773.1 = 0.6208
Ẇ = 0.6208·110 = 68.29 kW
Heat removed by the refrigerator
COPR = 243.1/(293.1 − 243.1) = 4.863
Q̇L = 4.863·68.29 = 332.1 kW
Answer
Q̇L = 332.1 kW
19.Waves, sound & optics
Answer: β = 80 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Total intensity
I = 10·I₁
Level
β = 70 + 10·log₁₀(10) = 80 dB
Answer
β = 80 dB
20.Waves, sound & optics
Answer: θ2 = 70.46 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …