Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3 m/s² along a runway. Find its speed v after 2000 m.
v₀ = 0a = 3 m/s²s = 2000 m
v = m/s
2.KinematicsHard
Ball A is dropped from rest from a height of 50 m. At the same instant ball B is thrown straight up from the ground directly below at 27 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 50 mv0B = 27 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 5 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 5 kgθ = 45°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 10.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 10.5 m/sθ = 25°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 40 m/sθ = 65°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is thrown from ground level at 30 m/s and 55° above the horizontal. It lands on the flat roof of a building 3 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 30 m/sθ = 55°hroof = 3 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.4. Find its speed v after it has slid 18 m along the slope.
θ = 40°μ = 0.4d = 18 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 4 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.1) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 4 mL = 3.5 mμ = 0.1k = 2500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 7 kg projectile moving horizontally at 7 m/s explodes into two fragments that move along the same line. The 3 kg fragment continues forwards at 56 m/s. Find the velocity v′2 of the 4 kg fragment (positive in the original direction).
M = 7 kgu = 7 m/sm1 = 3 kgv′1 = 56 m/sm2 = 4 kg
v′2 = m/s
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 12 m/s and bounces straight back at 14 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.6 kgvin = 12 m/svout = 14 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of oil, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 41 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 4 m. At section 1 the pressure is 210 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 2700 kJ of heat from a reservoir at 475 °C and rejects 1040 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 475 °CQH = 2700 kJQL = 1040 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 4 °C in a kitchen at 25 °C, removing heat from the cold space at 0.5 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = 4 °CQ̇L = 0.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 1 m long. The speed of sound is 343 m/s. Find the frequency f3 of its harmonic number 3.
v = 343 m/sn = 3L = 1 m
f3 = Hz
20.Waves, sound & opticsHard
Light of wavelength 450 nm falls on two slits 0.5 mm apart. The screen is 2.5 m away. Find the distance y4 from the central bright fringe to bright fringe number 4.
λ = 450 nmd = 0.5 mmL = 2.5 mm = 4
y4 = mm
3Solutions
1.Kinematics
Answer: v = 109.5 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3·2000) = 109.5 m/s
Answer
v = 109.5 m/s
(394.4 km/h)
2.Kinematics
Answer: t = 1.852 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
50 − ½g·t² = 27·t − ½g·t² → t = 50/27 = 1.852 s
Answer
t = 1.852 s
3.Newton’s laws
Answer: a = 5.549 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.15·cos 25°) = 5.48 m/s²
Distance
d = v₀²/(2a) = 10.5²/(2·5.48) = 10.06 m
Answer
d = 10.06 m
5.Projectile motion
Answer: H = 66.98 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 65° = 16.9 m/s
vy = v0·sin θ = 40·sin 65° = 36.25 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 36.25²/(2·9.81) = 66.98 m
Answer
H = 66.98 m
6.Projectile motion
Answer: x = 84.06 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 17.21 m/s, vy = 24.57 m/s
Time to land on the roof
Larger root: the ball is descending.
3 = 24.57·t − 4.905·t²
t = (24.57 + √(24.57² − 2·9.81·3))/9.81 = 4.885 s
Horizontal distance
x = vx·t = 17.21·4.885 = 84.06 m
Answer
x = 84.06 m
7.Work & energy
Answer: v = 10.9 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·18·(0.6428 − 0.4·0.766)) = 10.9 m/s
Answer
v = 10.9 m/s
8.Work & energy
Answer: x = 33.85 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(4 − 0.1·3.5) = 143.2 J
Maximum compression
½kx² = 143.2 → x = √(2·143.2/2500) = 0.3385 m = 33.85 cm
Answer
x = 33.85 cm
9.Momentum & collisions
Answer: v′2 = −29.75 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 7·7 = 49 kg·m/s
Momentum after
49 = 3·56 + 4·v′2
v′2 = (49 − 168)/4 = −29.75 m/s
Answer
v′2 = −29.75 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: Favg = 1560 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(14 + 12) = 15.6 N·s
Average force
Favg = J/Δt = 15.6/0.01 = 1560 N
Answer
Favg = 1560 N
11.Hydrostatic force
Answer: F = 29.43 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·1 = 29.43 kN
Answer
F = 29.43 kN
12.Hydrostatic force
Answer: ycp = 2.375 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2·4.5 = 77.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 475 + 273.15 = 748.1 K
Reversible heat ratio
TL = TH·QL/QH = 748.1·1040/2700 = 288.2 K = 15.03 °C
Answer
TL = 15.03 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.03789 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 0.5/13.2 = 0.03789 kW
Answer
Ẇmin = 0.03789 kW
19.Waves, sound & optics
Answer: f3 = 257.3 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·1/3 = 1.333 m
Frequency
f = v/λ = 343/1.333 = 257.3 Hz
Answer
f3 = 257.3 Hz
20.Waves, sound & optics
Answer: y4 = 9 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …