Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 240 km/h to take off and the usable runway is 1700 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 240 km/hs = 1700 m
a = m/s²
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 28 m/s² for 2 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 28 m/s²t1 = 2 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 7 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 7 kgθ = 45°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 75 N pulls the front 12 kg block; the 11 kg block is towed behind. The coefficient of kinetic friction is 0.1 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 11 kgm2 = 12 kgF = 75 Nμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 60° above the horizontal and lands 140 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 60°R = 140 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 14 m/s and 50° above the horizontal from the top of a 35 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 14 m/sθ = 50°h = 35 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A car travelling at 100 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 100 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 1 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.1) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 1 kgh = 4 mL = 1 mμ = 0.1k = 800 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1300 kg car moving at 8 m/s runs into a stationary 1200 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1300 kgv1 = 8 m/sm2 = 1200 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 0.35 kg ball hits a wall at 13 m/s and bounces straight back at 11 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.35 kgvin = 13 m/svout = 11 m/sΔt = 50 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 2 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 49 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A hose with an inner diameter of 25 mm siphons water from an open tank. The highest point C of the hose is 1 m above the water surface, and the outlet (open to the air) is 3.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 25 mmzC = +1 mz2 = −3.5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 310 g of O₂ occupy at 350 kPa and 30 °C? Treat it as an ideal gas.
A reversible (Carnot) heat engine takes in 3800 kJ of heat from a reservoir at 750 °C and rejects 1033 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 750 °CQH = 3800 kJQL = 1033 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 0 °C outside, delivering 7 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 0 °CQ̇H = 7 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe open at both ends is 0.5 m long. The speed of sound is 343 m/s. Find the frequency f1 of its fundamental (first harmonic).
v = 343 m/sn = 1L = 0.5 m
f1 = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 60 cm apart: lens 1 with f₁ = 15 cm and lens 2 with f₂ = 8 cm. An object stands 18 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 15 cmf2 = 8 cms = 60 cmdo = 18 cm
di2 = cm
3Solutions
1.Kinematics
Answer: a = 1.307 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 240/3.6 = 66.67 m/s
Acceleration
a = v²/(2s) = 66.67²/(2·1700) = 1.307 m/s²
Answer
a = 1.307 m/s²
2.Kinematics
Answer: hmax = 215.8 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 28·2 = 56 m/s
h₁ = ½·28·2² = 56 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 56²/(2·9.81) = 159.8 m
hmax = 56 + 159.8 = 215.8 m
Answer
hmax = 215.8 m
3.Newton’s laws
Answer: a = 5.203 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: v0 = 39.82 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·140/sin 120°) = 39.82 m/s
Answer
v0 = 39.82 m/s
6.Projectile motion
Answer: H = 40.86 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 14·sin 50° = 10.72 m/s
Rise above the cliff
Δh = vy²/(2g) = 10.72²/(2·9.81) = 5.862 m
Height above the ground
H = 35 + 5.862 = 40.86 m
Answer
H = 40.86 m
7.Work & energy
Answer: d = 56.18 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 100/3.6 = 27.78 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 27.78²/(2·0.7·9.81) = 56.18 m
Answer
d = 56.18 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 8.747 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(4 − 0.1·1) = 38.26 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.9) = 8.747 m/s
Answer
v = 8.747 m/s
9.Momentum & collisions
Answer: ΔK/K = 48 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1300·8/2500 = 4.16 m/s
Kinetic energy before and after
Kbefore = ½·1300·8² = 41600 J
Kafter = ½·2500·4.16² = 21632 J
Fraction lost
ΔK/K = 19968/41600 = 48 %
Answer
ΔK/K = 48 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 8.4 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.35·(11 + 13) = 8.4 N·s
Answer
J = 8.4 N·s
11.Hydrostatic force
Answer: F = 157 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·4 = 157 kN
Answer
F = 157 kN
12.Hydrostatic force
Answer: F = 70.39 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2/2 = 3.5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3.5·2 = 70.39 kN
Answer
F = 70.39 kN
13.Continuity & Bernoulli
Answer: Q = 30 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
p1 − p2 = ½ρv2²(1 − β⁴)
v2 = √(2·49000/(1000·(1 − 0.1296))) = 10.61 m/s
v1 = 3.82 m/s
Flow rate
Q = A2·v2 = 0.002827·10.61 = 0.03 m³/s = 30 L/s
Answer
Q = 30 L/s
14.Continuity & Bernoulli
Answer: Q = 4.068 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 750 + 273.15 = 1023 K
Reversible heat ratio
TL = TH·QL/QH = 1023·1033/3800 = 278.1 K = 4.985 °C
Answer
TL = 4.985 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5218 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 7/13.42 = 0.5218 kW
Answer
Ẇmin = 0.5218 kW
19.Waves, sound & optics
Answer: f1 = 343 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.5/1 = 1 m
Frequency
f = v/λ = 343/1 = 343 Hz
Answer
f1 = 343 Hz
20.Waves, sound & optics
Answer: di2 = 6.316 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.