Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 21 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 4 m/s². How long does it take the police car to catch up? Find t.
vcar = 21 m/sapolice = 4 m/s²v0,police = 0
t = s
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 28 m/s² for 3 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². How long after launch does it hit the ground? Find t.
a = 28 m/s²t1 = 3 sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
Masses of 1.5 kg and 0.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1.5 kgm2 = 0.5 kgg = 9.81 m/s²
T = N
4.Newton’s lawsHard
A 10 kg block on a ramp at 30° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 10 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 10 kgm2 = 10 kgθ = 30°μ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 38 m/s and 40° above the horizontal towards a wall 43 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 38 m/sθ = 40°x = 43 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 17 m/s and 15° above the horizontal from the top of a 30 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 17 m/sθ = 15°h = 30 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A 2000 kg car drives up an 8° slope at a constant 54 km/h. Air resistance and rolling resistance together amount to 500 N. Find the power P the wheels must deliver, in kW.
A spring of stiffness 800 N/m at the bottom of a 40° slope is compressed by 20 cm against a 3 kg block and released. The coefficient of kinetic friction between block and slope is 0.1. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1200 kg car moving at 14 m/s runs into a stationary 1200 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1200 kgv1 = 14 m/sm2 = 1200 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 9 m/s and bounces straight back at 5 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.6 kgvin = 9 m/svout = 5 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 4 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 200 mm to 75 mm. In the wide section the pressure is 360 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 5 m. At section 1 the pressure is 120 kPa and the velocity is 2.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 5 °C by removing 3.5 kW of heat, and rejects heat to the surroundings at 40 °C. Find the rate Q̇H at which it rejects heat.
TL = 5 °CTH = 40 °CQ̇L = 3.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 120 kW of heat from a source at 400 °C and rejects heat to the surroundings at 27 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -5 °C and also rejects heat to the surroundings at 27 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 400 °CT0 = 27 °CTL = -5 °CQ̇H = 120 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 10 cm in front of a thin diverging lens with a focal length of 5 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 10 cmf = −5 cm
di = cm
20.Waves, sound & opticsHard
Light of wavelength 550 nm passes through a single slit 0.15 mm wide. Find the width w of the central bright maximum on a screen 2.5 m away (between the first dark fringes on either side).
λ = 550 nma = 0.15 mmL = 2.5 m
w = mm
3Solutions
1.Kinematics
Answer: t = 10.5 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·21/4 = 10.5 s
Answer
t = 10.5 s
At that moment the police car moves at 2v = 42 m/s.
2.Kinematics
Answer: t = 21.51 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 28·3 = 84 m/s
h₁ = ½·28·3² = 126 m
Free flight to the ground
Solve −h₁ = v₁·t₂ − ½·g·t₂² for the positive root.
t₂ = (84 + √(84² + 2·9.81·126))/9.81 = 18.51 s
t = 3 + 18.51 = 21.51 s
Answer
t = 21.51 s
3.Newton’s laws
Answer: T = 7.357 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (1.5 − 0.5)·9.81/(1.5 + 0.5) = 4.905 m/s²
Tension from the lighter mass
T − m2·g = m2·a → T = 0.5·(9.81 + 4.905) = 7.357 N
Answer
T = 7.357 N
4.Newton’s laws
Answer: a = 2.028 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 98.1 N
m₁·g·sin θ = 49.05 N
μ·m₁·g·cos θ = 8.496 N
Acceleration of the system
a = (98.1 − 49.05 − 8.496)/20 = 2.028 m/s²
Answer
a = 2.028 m/s²
5.Projectile motion
Answer: y = 25.38 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 38·cos 40° = 29.11 m/s
t = x/vx = 43/29.11 = 1.477 s
Height at that time
y = 24.43·1.477 − ½·9.81·1.477² = 25.38 m
Answer
y = 25.38 m
The ball is still rising at the wall.
6.Projectile motion
Answer: v = 29.62 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 17·cos 15° = 16.42 m/s
vy0 = 17·sin 15° = 4.4 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(4.4² + 2·9.81·30) = 24.66 m/s
Impact speed
v = √(16.42² + 24.66²) = 29.62 m/s
Answer
v = 29.62 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: P = 48.46 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 2000·9.81 = 19620 N
mg·sin θ = 19620·sin 8° = 2731 N
F = 2731 + 500 = 3231 N
Power
v = 54/3.6 = 15 m/s
P = F·v = 3231·15 = 48459 W = 48.46 kW
Answer
P = 48.46 kW
8.Work & energy
Answer: d = 0.7557 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·800·0.2² = 16 J
Energy balance along the slope
m·g = 3·9.81 = 29.43 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 16/(29.43·(0.6428 + 0.1·0.766)) = 0.7557 m
Answer
d = 0.7557 m
9.Momentum & collisions
Answer: ΔK/K = 50 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1200·14/2400 = 7 m/s
Kinetic energy before and after
Kbefore = ½·1200·14² = 117600 J
Kafter = ½·2400·7² = 58800 J
Fraction lost
ΔK/K = 58800/117600 = 50 %
Answer
ΔK/K = 50 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 1680 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(5 + 9) = 8.4 N·s
Average force
Favg = J/Δt = 8.4/0.005 = 1680 N
Answer
Favg = 1680 N
11.Hydrostatic force
Answer: F = 82.77 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·3.75 = 82.77 kN
Answer
F = 82.77 kN
12.Hydrostatic force
Answer: ycp = 5.067 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2/2 = 5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5·2 = 98.1 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 1·2³/12 = 0.6667 m⁴
ycp = yc + Ic/(yc·A) = 5 + 0.6667/(5·2) = 5.067 m
Answer
ycp = 5.067 m
13.Continuity & Bernoulli
Answer: p2 = 346.1 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 383.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(400/300)·(383.1/288.1) = 8.865 L
Answer
V2 = 8.865 L
17.Heat engines & refrigerators
Answer: Q̇H = 3.94 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 40 + 273.15 = 313.1 K
TL = 5 + 273.15 = 278.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 3.5·313.1/278.1 = 3.94 kW
Answer
Q̇H = 3.94 kW
Power input: Ẇ = 0.4404 kW.
18.Heat engines & refrigerators
Answer: Q̇L = 557.2 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
T0 = 27 + 273.15 = 300.1 K
TL = -5 + 273.15 = 268.1 K
Engine work
η = 1 − 300.1/673.1 = 0.5541
Ẇ = 0.5541·120 = 66.49 kW
Heat removed by the refrigerator
COPR = 268.1/(300.1 − 268.1) = 8.38
Q̇L = 8.38·66.49 = 557.2 kW
Answer
Q̇L = 557.2 kW
19.Waves, sound & optics
Answer: di = −3.333 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−5) − 1/10
di = −3.333 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −3.333 cm
20.Waves, sound & optics
Answer: w = 18.33 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …