Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 4 m/s² until it stops. How long does braking take? Find t.
v₀ = 50 km/ha = −4 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 12 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 12 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
Masses of 3.5 kg and 2.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 3.5 kgm2 = 2.5 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 120 N pulls the front 8 kg block; the 6 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 6 kgm2 = 8 kgF = 120 Nμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 12 m/sθ = 35°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 25 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 23 m/sθ = 45°h = 25 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 110 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
v = 110 km/hμ = 0.4g = 9.81 m/s²
d = m
8.Work & energyHard
A 5 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4.5 m long (μ = 0.25) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 5 mL = 4.5 mμ = 0.25k = 800 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2 kg glider moving at 8 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 5 kgv1 = 8 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.1 kg ball hits a wall at 23 m/s and bounces straight back at 15 m/s. The contact lasts 40 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.1 kgvin = 23 m/svout = 15 m/sΔt = 40 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 200 mm to 50 mm. In the wide section the pressure is 260 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 75 mm and a gauge pressure of 70 kPa. The nozzle exit diameter is 40 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 525 °C and a cold reservoir at 25 °C. It takes in 800 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 525 °CTL = 25 °CQH = 800 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 0 °C outside, delivering 14 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = 0 °CQ̇H = 14 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 40 cm in front of a thin converging lens with a focal length of 20 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 40 cmf = 20 cm
di = cm
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.5 and a cladding with n₂ = 1.48. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.5n2 = 1.48n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: t = 3.472 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 13.89/4 = 3.472 s
Answer
t = 3.472 s
2.Kinematics
Answer: t = 4.161 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 12·t − ½·9.81·t²
4.905·t² − 12·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (12 + √(12² + 2·9.81·35))/9.81 = 4.161 s
Answer
t = 4.161 s
3.Newton’s laws
Answer: a = 1.635 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (3.5 − 2.5)·9.81/(3.5 + 2.5) = 1.635 m/s²
Answer
a = 1.635 m/s²
4.Newton’s laws
Answer: T = 51.43 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: H = 2.415 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 35° = 9.83 m/s
vy = v0·sin θ = 12·sin 35° = 6.883 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 6.883²/(2·9.81) = 2.415 m
Answer
H = 2.415 m
6.Projectile motion
Answer: t = 4.459 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 23·cos 45° = 16.26 m/s
vy = v0·sin θ = 23·sin 45° = 16.26 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 25 + 16.26·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (16.26 + √(264.5 + 490.5))/9.81 = 4.459 s
Answer
t = 4.459 s
7.Work & energy
Answer: d = 119 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 110/3.6 = 30.56 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 30.56²/(2·0.4·9.81) = 119 m
Answer
d = 119 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 68.93 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(5 − 0.25·4.5) = 190.1 J
Maximum compression
½kx² = 190.1 → x = √(2·190.1/800) = 0.6893 m = 68.93 cm
Answer
x = 68.93 cm
9.Momentum & collisions
Answer: v′1 = −3.429 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 5)/(2 + 5)·8 = −3.429 m/s
v′2 = 2·2/(2 + 5)·8 = 4.571 m/s
Answer
v′1 = −3.429 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: J = 3.8 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.1·(15 + 23) = 3.8 N·s
Answer
J = 3.8 N·s
11.Hydrostatic force
Answer: F = 138 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.75·3.75 = 138 kN
Answer
F = 138 kN
12.Hydrostatic force
Answer: F = 32.45 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1.5/2 = 1.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·1.75·1.5 = 32.45 kN
Answer
F = 32.45 kN
13.Continuity & Bernoulli
Answer: p2 = 228.1 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 40/75 = 0.5333
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·70000/(1000·0.9191)) = 12.34 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 12.34²/(2·9.81) = 7.764 m
Answer
H = 7.764 m
15.Ideal gas law
Answer: P = 905.8 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 480/32 = 15 mol
T = 90 + 273.15 = 363.1 K
Pressure
P = nRT/V = 15·8.314·363.1/0.05 = 905.8 kPa
Answer
P = 905.8 kPa
16.Ideal gas law
Answer: ρ = 1.274 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 180 + 273.15 = 453.1 K
Density
ρ = 150·32/(8.314·453.1) = 1.274 kg/m³
Answer
ρ = 1.274 kg/m³
17.Heat engines & refrigerators
Answer: Wmax = 501.2 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 525 + 273.15 = 798.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/798.1 = 62.64 %
Maximum work
Wmax = ηmax·QH = 0.6264·800 = 501.2 kJ
Answer
Wmax = 501.2 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.9551 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 14/14.66 = 0.9551 kW
Answer
Ẇmin = 0.9551 kW
19.Waves, sound & optics
Answer: di = 40 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/20 − 1/40
di = 40 cm
Ray diagram
real, on the far side of the lens
Answer
di = 40 cm
20.Waves, sound & optics
Answer: θa = 14.13 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.