Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 4 m/s² along a runway. Find its speed v after 1500 m.
v₀ = 0a = 4 m/s²s = 1500 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 9 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 9 m/sh₀ = 25 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
An 18 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 18 kgθ = 45°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
An 8 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 8 kgm2 = 2.5 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 28 m/sθ = 65°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 11 m/s and 35° above the horizontal from the top of a 15 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 11 m/sθ = 35°h = 15 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 12 m along the slope.
θ = 35°μ = 0.35d = 12 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A spring of stiffness 5000 N/m at the bottom of a 15° slope is compressed by 5 cm against a 3 kg block and released. The coefficient of kinetic friction between block and slope is 0.3. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1.5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 1.5 kgm2 = 3.5 kgv1 = 9 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 1.5 kg block hanging from light strings 0.6 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 1.5 kgL = 0.6 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 25 mm. In the wide section the pressure is 300 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 50 mm siphons water from an open tank. The highest point C of the hose is 3 m above the water surface, and the outlet (open to the air) is 2.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A heat engine receives heat from a source at 550 °C and rejects heat to the surroundings at 20 °C. Its actual thermal efficiency is 39%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 550 °CTL = 20 °Cη = 39%
ηII = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1050 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 35 °C. Both engines produce the same work. Find Tm in °C.
TH = 1050 °CTL = 35 °C
Tm = °C
19.Waves, sound & opticsMedium
An object 4 cm tall stands 10 cm in front of a thin converging lens with a focal length of 15 cm. Find the image height hi (negative for an inverted image).
ho = 4 cmdo = 10 cmf = 15 cm
hi = cm
20.Waves, sound & opticsHard
Light of wavelength 650 nm passes through a single slit 0.1 mm wide. Find the angle θ2 of dark fringe number 2 from the straight-through direction.
λ = 650 nma = 0.1 mmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: v = 109.5 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·4·1500) = 109.5 m/s
Answer
v = 109.5 m/s
(394.4 km/h)
2.Kinematics
Answer: t = 3.354 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−25 = 9·t − ½·9.81·t²
4.905·t² − 9·t − 25 = 0
Solve the quadratic
Only the positive root is physical.
t = (9 + √(9² + 2·9.81·25))/9.81 = 3.354 s
Answer
t = 3.354 s
3.Newton’s laws
Answer: a = 4.856 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 65° = 11.83 m/s
vy = v0·sin θ = 28·sin 65° = 25.38 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·25.38/9.81 = 5.174 s
Horizontal distance
x = vx·t = 11.83·5.174 = 61.22 m
Answer
x = 61.22 m
6.Projectile motion
Answer: α = 63.76 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 11·cos 35° = 9.011 m/s
vy0 = 11·sin 35° = 6.309 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(6.309² + 2·9.81·15) = 18.28 m/s
Impact angle
tan α = vy/vx = 18.28/9.011 → α = 63.76°
Answer
α = 63.76°
7.Work & energy
Answer: v = 8.218 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·12·(0.5736 − 0.35·0.8192)) = 8.218 m/s
Answer
v = 8.218 m/s
8.Work & energy
Answer: d = 0.3871 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 5 cm = 0.05 m
½kx² = ½·5000·0.05² = 6.25 J
Energy balance along the slope
m·g = 3·9.81 = 29.43 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 6.25/(29.43·(0.2588 + 0.3·0.9659)) = 0.3871 m
Answer
d = 0.3871 m
9.Momentum & collisions
Answer: v′1 = −3.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 3.5)/(1.5 + 3.5)·9 = −3.6 m/s
v′2 = 2·1.5/(1.5 + 3.5)·9 = 5.4 m/s
Answer
v′1 = −3.6 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 158.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.6·(1 − cos 30°) = 0.08038 m
Speed after impact
V = √(2·9.81·0.08038) = 1.256 m/s
Collision
v = (m + M)·V/m = 1.512·1.256/0.012 = 158.2 m/s
Answer
v = 158.2 m/s
11.Hydrostatic force
Answer: F = 117.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 3/2 = 4 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·3 = 117.7 kN
Answer
F = 117.7 kN
12.Hydrostatic force
Answer: F = 80.93 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·3 = 80.93 kN
Answer
F = 80.93 kN
13.Continuity & Bernoulli
Answer: p2 = 268.1 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: V = 196.6 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 470/16.04 = 29.3 mol
T = 90 + 273.15 = 363.1 K
Volume
V = nRT/P = 29.3·8.314·363.1/450 = 196.6 L
Answer
V = 196.6 L
16.Ideal gas law
Answer: V2 = 7.935 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 473.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(100/200)·(473.1/298.1) = 7.935 L
Answer
V2 = 7.935 L
17.Heat engines & refrigerators
Answer: ηII = 60.57 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηCarnot = 1 − 293.1/823.1 = 64.39 %
Second-law efficiency
ηII = η/ηCarnot = 39/64.39 = 60.57 %
Answer
ηII = 60.57 %
18.Heat engines & refrigerators
Answer: Tm = 542.5 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1050 + 273.15 = 1323 K
TL = 35 + 273.15 = 308.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1323 + 308.1)/2 = 815.7 K = 542.5 °C
Answer
Tm = 542.5 °C
19.Waves, sound & optics
Answer: hi = 12 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/15 − 1/10
di = −30 cm
Magnification and height
m = −(−30)/10 = 3
hi = 3·4 = 12 cm
Answer
hi = 12 cm
20.Waves, sound & optics
Answer: θ2 = 0.7449 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …