Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 45 km/h sees an obstacle. Her reaction time is 0.9 s, after which the car brakes with a constant deceleration of 8 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 45 km/htr = 0.9 sa = −8 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 8 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 8 m/sh₀ = 10 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 25 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 110 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 25 kgF = 110 Nθ = 35°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a ramp at 30° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 9 kg mass. The hanging mass moves down. The ramp is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3.5 kgm2 = 9 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 38 m/sθ = 20°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 20° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 12 m/sθ = 20°h = 40 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.1. Find its speed v after it has slid 5 m along the slope.
θ = 25°μ = 0.1d = 5 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 10 kg cart is released from rest at a height of 16 m on a smooth track that leads into a vertical circular loop of radius 4 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 10 kgh = 16 mR = 4 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 1500 kg car moving at 20 m/s runs into a stationary 1700 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1500 kgv1 = 20 m/sm2 = 1700 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.1 kg ball hits a wall at 25 m/s and bounces straight back at 12 m/s. The contact lasts 40 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.1 kgvin = 25 m/svout = 12 m/sΔt = 40 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 1.5 m above the orifice and the discharge coefficient is 0.62. Find the flow rate Q. Use g = 9.81 m/s².
d = 30 mmh = 1.5 mCd = 0.62g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 10 m. At section 1 the pressure is 190 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 500 °C and rejects heat to the surroundings at 15 °C. Its actual thermal efficiency is 47%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 500 °CTL = 15 °Cη = 47%
ηII = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 60 kW of heat from a source at 550 °C and rejects heat to the surroundings at 27 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -5 °C and also rejects heat to the surroundings at 27 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 550 °CT0 = 27 °CTL = -5 °CQ̇H = 60 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object 5 cm tall stands 25 cm in front of a thin converging lens with a focal length of 8 cm. Find the image height hi (negative for an inverted image).
ho = 5 cmdo = 25 cmf = 8 cm
hi = cm
20.Waves, sound & opticsHard
Two thin lenses share an axis, 25 cm apart: lens 1 with f₁ = 20 cm and lens 2 with f₂ = 15 cm. An object stands 18 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 20 cmf2 = 15 cms = 25 cmdo = 18 cm
di2 = cm
3Solutions
1.Kinematics
Answer: d = 21.02 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Reaction distance
d1 = v₀·tr = 12.5·0.9 = 11.25 m
Braking distance
d2 = v₀²/(2a) = 12.5²/(2·8) = 9.766 m
Total
d = 11.25 + 9.766 = 21.02 m
Answer
d = 21.02 m
2.Kinematics
Answer: t = 2.46 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−10 = 8·t − ½·9.81·t²
4.905·t² − 8·t − 10 = 0
Solve the quadratic
Only the positive root is physical.
t = (8 + √(8² + 2·9.81·10))/9.81 = 2.46 s
Answer
t = 2.46 s
3.Newton’s laws
Answer: a = 2.147 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 245.3 − 110·sin 35° = 182.2 N
Horizontal forces
m·a = F·cos θ − μ·N = 90.11 − 36.43
a = 53.68/25 = 2.147 m/s²
Answer
a = 2.147 m/s²
4.Newton’s laws
Answer: a = 5.69 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 88.29 N
m₁·g·sin θ = 17.17 N
μ·m₁·g·cos θ = 0 N
Acceleration of the system
a = (88.29 − 17.17 − 0)/12.5 = 5.69 m/s²
Answer
a = 5.69 m/s²
5.Projectile motion
Answer: x = 94.62 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 38·cos 20° = 35.71 m/s
vy = v0·sin θ = 38·sin 20° = 13 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13/9.81 = 2.65 s
Horizontal distance
x = vx·t = 35.71·2.65 = 94.62 m
Answer
x = 94.62 m
6.Projectile motion
Answer: t = 3.305 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 20° = 11.28 m/s
vy = v0·sin θ = 12·sin 20° = 4.104 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 4.104·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (4.104 + √(16.84 + 784.8))/9.81 = 3.305 s
Answer
t = 3.305 s
7.Work & energy
Answer: v = 5.707 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·5·(0.4226 − 0.1·0.9063)) = 5.707 m/s
Answer
v = 5.707 m/s
8.Work & energy
Answer: N = 294.3 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(16 − 8) = 157 m²/s²
Forces at the top
m·g = 10·9.81 = 98.1 N
N = mv²/R − mg = 10·157/4 − 98.1 = 294.3 N
Answer
N = 294.3 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: ΔK = 159375 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1500·20/3200 = 9.375 m/s
Kinetic energy before and after
Kbefore = ½·1500·20² = 300000 J
Kafter = ½·3200·9.375² = 140625 J
Energy lost
ΔK = 300000 − 140625 = 159375 J
Answer
ΔK = 159375 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 3.7 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.1·(12 + 25) = 3.7 N·s
Answer
J = 3.7 N·s
11.Hydrostatic force
Answer: F = 33.11 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·1.5 = 33.11 kN
Answer
F = 33.11 kN
12.Hydrostatic force
Answer: ycp = 2.333 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.25·1.5 = 33.94 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·1.5) = 5.425 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηCarnot = 1 − 288.1/773.1 = 62.73 %
Second-law efficiency
ηII = η/ηCarnot = 47/62.73 = 74.92 %
Answer
ηII = 74.92 %
18.Heat engines & refrigerators
Answer: Q̇L = 319.4 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
T0 = 27 + 273.15 = 300.1 K
TL = -5 + 273.15 = 268.1 K
Engine work
η = 1 − 300.1/823.1 = 0.6354
Ẇ = 0.6354·60 = 38.12 kW
Heat removed by the refrigerator
COPR = 268.1/(300.1 − 268.1) = 8.38
Q̇L = 8.38·38.12 = 319.4 kW
Answer
Q̇L = 319.4 kW
19.Waves, sound & optics
Answer: hi = −2.353 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/8 − 1/25
di = 11.76 cm
Magnification and height
m = −11.76/25 = −0.4706
hi = −0.4706·5 = −2.353 cm
Answer
hi = −2.353 cm
20.Waves, sound & optics
Answer: di2 = 16.18 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.