Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 22 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 3.5 m/s². How far from its starting point does the police car catch up? Find d.
vcar = 22 m/sapolice = 3.5 m/s²v0,police = 0
d = m
2.KinematicsHard
A ball is thrown straight up at 12 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 12 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 9 kg block slides down a frictionless slope at 30° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 6 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3.5 kgm2 = 6 kgμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 25° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 30 m/sθ = 25°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 20 m/sθ = 55°h = 45 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 1500 N/m. A 0.2 kg ball is placed on it and the spring is compressed by 10 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.2 kgk = 1500 N/mx = 10 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 2 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 20 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 3 m up the slope.
A 5 kg projectile moving horizontally at 19 m/s explodes into two fragments that move along the same line. The 3 kg fragment continues forwards at 55 m/s. Find the velocity v′2 of the 2 kg fragment (positive in the original direction).
M = 5 kgu = 19 m/sm1 = 3 kgv′1 = 55 m/sm2 = 2 kg
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 1400 kg car travelling east at 22 m/s collides with a 1000 kg car travelling north at 25 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1400 kgv1 = 22 m/s (E)m2 = 1000 kgv2 = 25 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 3 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 20 mm. The water level is kept 4.5 m above the orifice and the discharge coefficient is 0.62. Find the flow rate Q. Use g = 9.81 m/s².
d = 20 mmh = 4.5 mCd = 0.62g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A hose with an inner diameter of 25 mm siphons water from an open tank. The highest point C of the hose is 2 m above the water surface, and the outlet (open to the air) is 4.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A heat engine works between a hot reservoir at 625 °C and a cold reservoir at 15 °C. It takes in 900 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 625 °CTL = 15 °CQH = 900 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -10 °C in a kitchen at 32 °C, removing heat from the cold space at 1 kW. Find the highest possible coefficient of performance COPmax.
TH = 32 °CTL = -10 °CQ̇L = 1 kW
COPmax =
19.Waves, sound & opticsMedium
A string fixed at both ends must have its harmonic number 2 at 462 Hz; waves travel on it at 300 m/s. Find its length L.
v = 300 m/sn = 2f2 = 462 Hz
L = m
20.Waves, sound & opticsHard
An object is 30 cm in front of a convex mirror with a radius of curvature of 40 cm. Find the magnification m (negative for an inverted image).
do = 30 cmR = 40 cm
m =
3Solutions
1.Kinematics
Answer: d = 276.6 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·22/3.5 = 12.57 s
Distance
d = v·t = 22·12.57 = 276.6 m
Answer
d = 276.6 m
At that moment the police car moves at 2v = 44 m/s.
2.Kinematics
Answer: t = 4.161 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 12·t − ½·9.81·t²
4.905·t² − 12·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (12 + √(12² + 2·9.81·35))/9.81 = 4.161 s
Answer
t = 4.161 s
3.Newton’s laws
Answer: a = 4.905 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 25° = 27.19 m/s
vy = v0·sin θ = 30·sin 25° = 12.68 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 12.68²/(2·9.81) = 8.193 m
Answer
H = 8.193 m
6.Projectile motion
Answer: t = 5.129 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 55° = 11.47 m/s
vy = v0·sin θ = 20·sin 55° = 16.38 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 16.38·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (16.38 + √(268.4 + 882.9))/9.81 = 5.129 s
Answer
t = 5.129 s
7.Work & energy
Answer: h = 3.823 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·1500·0.1² = 7.5 J
Height
m·g = 0.2·9.81 = 1.962 N
h = ½kx²/(mg) = 7.5/1.962 = 3.823 m
Answer
h = 3.823 m
8.Work & energy
Answer: v = 5.86 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 2·9.81 = 19.62 N
mg·sin θ = 6.71 N
μ·mg·cos θ = 1.844 N
Work–energy
½mv² = (20 − 8.554)·3 = 34.34 J
v = √(2·34.34/2) = 5.86 m/s
Answer
v = 5.86 m/s
9.Momentum & collisions
Answer: v′2 = −35 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 5·19 = 95 kg·m/s
Momentum after
95 = 3·55 + 2·v′2
v′2 = (95 − 165)/2 = −35 m/s
Answer
v′2 = −35 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: θ = 39.07 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1400·22 = 30800 kg·m/s
py = 1000·25 = 25000 kg·m/s
Direction
tan θ = py/px = 0.8117 → θ = 39.07°
Answer
θ = 39.07°
11.Hydrostatic force
Answer: F = 98.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2/2 = 5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5·2 = 98.1 kN
Answer
F = 98.1 kN
12.Hydrostatic force
Answer: ycp = 4.667 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·4.5·9 = 349.6 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·4.5) = 9.396 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: V = 77.76 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 160/16.04 = 9.975 mol
T = 55 + 273.15 = 328.1 K
Volume
V = nRT/P = 9.975·8.314·328.1/350 = 77.76 L
Answer
V = 77.76 L
16.Ideal gas law
Answer: V2 = 0.7974 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(150/550)·(443.1/303.1) = 0.7974 L
Answer
V2 = 0.7974 L
17.Heat engines & refrigerators
Answer: Wmax = 611.3 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 625 + 273.15 = 898.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/898.1 = 67.92 %
Maximum work
Wmax = ηmax·QH = 0.6792·900 = 611.3 kJ
Answer
Wmax = 611.3 kJ
18.Heat engines & refrigerators
Answer: COPmax = 6.265
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 300/462 = 0.6494 m
Length
L = nλ/2 = 2·0.6494/2 = 0.6494 m
Answer
L = 0.6494 m
20.Waves, sound & optics
Answer: m = 0.4
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.