Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 4 m/s² along a runway. Find its speed v after 600 m.
v₀ = 0a = 4 m/s²s = 600 m
v = m/s
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 32 m/s² for 1.5 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². How long after launch does it hit the ground? Find t.
a = 32 m/s²t1 = 1.5 sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 6.5 m/s and comes to rest after 22 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 6.5 m/sd = 22 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 9.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 9.5 kgm2 = 4 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 22 m/sθ = 70°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 14 m/s and 70° above the horizontal from the top of a 10 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 14 m/sθ = 70°h = 10 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.1. Find its speed v after it has slid 16 m along the slope.
θ = 35°μ = 0.1d = 16 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 4 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.2) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 2 mL = 2.5 mμ = 0.2k = 800 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3 kgm2 = 0.5 kgv1 = 5 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 28 m/s and bounces straight back at 12 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.3 kgvin = 28 m/svout = 12 m/sΔt = 50 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 200 mm to 100 mm. In the wide section the pressure is 380 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 100 mm while rising 4 m. At section 1 the pressure is 300 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 750 °C and rejects heat to the surroundings at 35 °C. Its actual thermal efficiency is 35%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 750 °CTL = 35 °Cη = 35%
ηII = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 100 kW of heat from a source at 800 °C and rejects heat to the surroundings at 25 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at 0 °C and also rejects heat to the surroundings at 25 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 800 °CT0 = 25 °CTL = 0 °CQ̇H = 100 kW
Q̇L = kW
19.Waves, sound & opticsMedium
Light travels in diamond (n = 2.42) towards a flat boundary with ethanol (n = 1.36). Find the critical angle θc beyond which it is totally reflected.
n1 = 2.42n2 = 1.36
θc = °
20.Waves, sound & opticsHard
Two thin lenses share an axis, 50 cm apart: lens 1 with f₁ = 8 cm and lens 2 with f₂ = −10 cm. An object stands 30 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 8 cmf2 = −10 cms = 50 cmdo = 30 cm
di2 = cm
3Solutions
1.Kinematics
Answer: v = 69.28 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·4·600) = 69.28 m/s
Answer
v = 69.28 m/s
(249.4 km/h)
2.Kinematics
Answer: t = 11.99 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 32·1.5 = 48 m/s
h₁ = ½·32·1.5² = 36 m
Free flight to the ground
Solve −h₁ = v₁·t₂ − ½·g·t₂² for the positive root.
t₂ = (48 + √(48² + 2·9.81·36))/9.81 = 10.49 s
t = 1.5 + 10.49 = 11.99 s
Answer
t = 11.99 s
3.Newton’s laws
Answer: μ = 0.09788
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 6.5²/(2·22) = 0.9602 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 0.9602/9.81 = 0.09788
Answer
μ = 0.09788
4.Newton’s laws
Answer: T = 33.14 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 22·cos 70° = 7.524 m/s
vy = v0·sin θ = 22·sin 70° = 20.67 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 20.67²/(2·9.81) = 21.78 m
Answer
H = 21.78 m
6.Projectile motion
Answer: H = 18.82 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 14·sin 70° = 13.16 m/s
Rise above the cliff
Δh = vy²/(2g) = 13.16²/(2·9.81) = 8.821 m
Height above the ground
H = 10 + 8.821 = 18.82 m
Answer
H = 18.82 m
7.Work & energy
Answer: v = 12.42 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·16·(0.5736 − 0.1·0.8192)) = 12.42 m/s
Answer
v = 12.42 m/s
8.Work & energy
Answer: x = 38.36 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(2 − 0.2·2.5) = 58.86 J
Maximum compression
½kx² = 58.86 → x = √(2·58.86/800) = 0.3836 m = 38.36 cm
Answer
x = 38.36 cm
9.Momentum & collisions
Answer: v′2 = 8.571 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 0.5)/(3 + 0.5)·5 = 3.571 m/s
v′2 = 2·3/(3 + 0.5)·5 = 8.571 m/s
Answer
v′2 = 8.571 m/s
10.Momentum & collisions
Answer: J = 12 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(12 + 28) = 12 N·s
Answer
J = 12 N·s
11.Hydrostatic force
Answer: F = 264.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·6 = 264.9 kN
Answer
F = 264.9 kN
12.Hydrostatic force
Answer: ycp = 1.4 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1.5/2 = 1.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.25·1.5 = 18.39 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 423.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(350/650)·(423.1/313.1) = 7.276 L
Answer
V2 = 7.276 L
17.Heat engines & refrigerators
Answer: ηII = 50.08 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηCarnot = 1 − 308.1/1023 = 69.88 %
Second-law efficiency
ηII = η/ηCarnot = 35/69.88 = 50.08 %
Answer
ηII = 50.08 %
18.Heat engines & refrigerators
Answer: Q̇L = 789 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 800 + 273.15 = 1073 K
T0 = 25 + 273.15 = 298.1 K
TL = 0 + 273.15 = 273.1 K
Engine work
η = 1 − 298.1/1073 = 0.7222
Ẇ = 0.7222·100 = 72.22 kW
Heat removed by the refrigerator
COPR = 273.1/(298.1 − 273.1) = 10.93
Q̇L = 10.93·72.22 = 789 kW
Answer
Q̇L = 789 kW
19.Waves, sound & optics
Answer: θc = 34.19 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.36/2.42 = 0.562
Critical angle
θc = arcsin(0.562) = 34.19°
Answer
θc = 34.19°
20.Waves, sound & optics
Answer: di2 = −7.963 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.