Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 72 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 6 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 6 m/sh₀ = 20 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 9 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 20°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 9 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 9 m/sθ = 25°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 12 m/sθ = 45°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 25° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 33 m/sθ = 25°h = 45 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 120 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
v = 120 km/hμ = 0.4g = 9.81 m/s²
d = m
8.Work & energyHard
A 2.5 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.1) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2.5 kgh = 5 mL = 3.5 mμ = 0.1k = 2500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1.5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 1.5 kgm2 = 0.5 kgv1 = 11 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 900 kg car travelling east at 9 m/s collides with a 1400 kg car travelling north at 25 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 900 kgv1 = 9 m/s (E)m2 = 1400 kgv2 = 25 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 1 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
A pitot-static tube in a water pipe reads a difference of 19 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 19 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 150 mm to 100 mm while rising 8 m. At section 1 the pressure is 340 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 425 °C and a cold reservoir at 30 °C. It takes in 1500 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 425 °CTL = 30 °CQH = 1500 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is 7 °C outside, delivering 4 kW of heat to the house. Find the highest possible coefficient of performance COPmax.
TH = 21 °CTL = 7 °CQ̇H = 4 kW
COPmax =
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with acrylic (n = 1.49) for every angle of incidence above 40°. Find the refractive index n1 of the block.
θc = 40°n2 = 1.49
n1 =
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls on two slits 0.4 mm apart. The screen is 1.5 m away. Find the distance y2 from the central bright fringe to bright fringe number 2.
λ = 532 nmd = 0.4 mmL = 1.5 mm = 2
y2 = mm
3Solutions
1.Kinematics
Answer: s = 66.67 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 20²/(2·3) = 66.67 m
Answer
s = 66.67 m
2.Kinematics
Answer: hmax = 21.83 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 6²/(2·9.81) = 1.835 m
Height above the ground
hmax = 20 + 1.835 = 21.83 m
Answer
hmax = 21.83 m
3.Newton’s laws
Answer: a = 1.512 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.15·cos 25°) = 5.48 m/s²
Distance
d = v₀²/(2a) = 9²/(2·5.48) = 7.391 m
Answer
d = 7.391 m
5.Projectile motion
Answer: t = 1.73 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 45° = 8.485 m/s
vy = v0·sin θ = 12·sin 45° = 8.485 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·8.485/9.81 = 1.73 s
Answer
t = 1.73 s
6.Projectile motion
Answer: t = 4.768 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 33·cos 25° = 29.91 m/s
vy = v0·sin θ = 33·sin 25° = 13.95 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 13.95·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (13.95 + √(194.5 + 882.9))/9.81 = 4.768 s
Answer
t = 4.768 s
7.Work & energy
Answer: d = 141.6 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 120/3.6 = 33.33 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 33.33²/(2·0.4·9.81) = 141.6 m
Answer
d = 141.6 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 9.552 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(5 − 0.1·3.5) = 114 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.65) = 9.552 m/s
Answer
v = 9.552 m/s
9.Momentum & collisions
Answer: v′1 = 5.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 0.5)/(1.5 + 0.5)·11 = 5.5 m/s
v′2 = 2·1.5/(1.5 + 0.5)·11 = 16.5 m/s
Answer
v′1 = 5.5 m/s
10.Momentum & collisions
Answer: v′ = 15.62 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·3 = 66.22 kN
Answer
F = 66.22 kN
12.Hydrostatic force
Answer: ycp = 2.8 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·9 = 220.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 3·3³/12 = 6.75 m⁴
ycp = yc + Ic/(yc·A) = 2.5 + 6.75/(2.5·9) = 2.8 m
Answer
ycp = 2.8 m
13.Continuity & Bernoulli
Answer: v = 6.164 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·19000/1000) = 6.164 m/s
Answer
v = 6.164 m/s
14.Continuity & Bernoulli
Answer: p2 = 259.5 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 425 + 273.15 = 698.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/698.1 = 56.58 %
Maximum work
Wmax = ηmax·QH = 0.5658·1500 = 848.7 kJ
Answer
Wmax = 848.7 kJ
18.Heat engines & refrigerators
Answer: COPmax = 21.01
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.49/0.6428 = 2.318
Answer
n1 = 2.318
20.Waves, sound & optics
Answer: y2 = 3.99 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …