Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 80 km/h brakes with a constant deceleration of 8 m/s² until it stops. Find the braking distance s.
v₀ = 80 km/ha = −8 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 30 m. At the same instant ball B is thrown straight up from the ground directly below at 18 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 30 mv0B = 18 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 19 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 19 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 145 N pulls the front 5 kg block; the 4 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 4 kgm2 = 5 kgF = 145 Nμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 26 m/sθ = 30°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 21 m/s and 20° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 21 m/sθ = 20°h = 50 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A car travelling at 90 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 90 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A spring of stiffness 2000 N/m at the bottom of a 30° slope is compressed by 12 cm against a 5 kg block and released. The coefficient of kinetic friction between block and slope is 0.25. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 0.5 kg glider moving at 4 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 0.5 kgm2 = 4 kgv1 = 4 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.15 kg ball hits a wall at 9 m/s and bounces straight back at 10 m/s. The contact lasts 50 ms. Find the average force Favg of the wall on the ball.
m = 0.15 kgvin = 9 m/svout = 10 m/sΔt = 50 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a wind tunnel reads a difference of 1350 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 1350 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 10 m. At section 1 the pressure is 210 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 425 °C and a cold reservoir at 25 °C. Find the highest possible thermal efficiency ηmax.
TH = 425 °CTL = 25 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is 7 °C outside, delivering 11 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = 7 °CQ̇H = 11 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe open at both ends must have its harmonic number 3 at 792 Hz. The speed of sound is 343 m/s. Find the length L of the pipe.
v = 343 m/sn = 3f3 = 792 Hz
L = m
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.55 and a cladding with n₂ = 1.45. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.55n2 = 1.45n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: s = 30.86 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 22.22²/(2·8) = 30.86 m
Answer
s = 30.86 m
2.Kinematics
Answer: t = 1.667 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
30 − ½g·t² = 18·t − ½g·t² → t = 30/18 = 1.667 s
Answer
t = 1.667 s
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: H = 8.614 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 26·cos 30° = 22.52 m/s
vy = v0·sin θ = 26·sin 30° = 13 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 13²/(2·9.81) = 8.614 m
Answer
H = 8.614 m
6.Projectile motion
Answer: α = 58.45 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 21·cos 20° = 19.73 m/s
vy0 = 21·sin 20° = 7.182 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(7.182² + 2·9.81·50) = 32.13 m/s
Impact angle
tan α = vy/vx = 32.13/19.73 → α = 58.45°
Answer
α = 58.45°
7.Work & energy
Answer: d = 45.51 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 90/3.6 = 25 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 25²/(2·0.7·9.81) = 45.51 m
Answer
d = 45.51 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: d = 0.4097 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 12 cm = 0.12 m
½kx² = ½·2000·0.12² = 14.4 J
Energy balance along the slope
m·g = 5·9.81 = 49.05 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 14.4/(49.05·(0.5 + 0.25·0.866)) = 0.4097 m
Answer
d = 0.4097 m
9.Momentum & collisions
Answer: v′2 = 0.8889 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 4)/(0.5 + 4)·4 = −3.111 m/s
v′2 = 2·0.5/(0.5 + 4)·4 = 0.8889 m/s
Answer
v′2 = 0.8889 m/s
10.Momentum & collisions
Answer: Favg = 57 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.15·(10 + 9) = 2.85 N·s
Average force
Favg = J/Δt = 2.85/0.05 = 57 N
Answer
Favg = 57 N
11.Hydrostatic force
Answer: F = 58.86 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·2 = 58.86 kN
Answer
F = 58.86 kN
12.Hydrostatic force
Answer: F = 90.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2·4.5 = 90.5 kN
Answer
F = 90.5 kN
13.Continuity & Bernoulli
Answer: v = 47.43 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·1350/1.2) = 47.43 m/s
Answer
v = 47.43 m/s
14.Continuity & Bernoulli
Answer: p2 = 96.54 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 353.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(250/650)·(353.1/283.1) = 4.797 L
Answer
V2 = 4.797 L
17.Heat engines & refrigerators
Answer: ηmax = 57.29 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 425 + 273.15 = 698.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/698.1 = 57.29 %
Answer
ηmax = 57.29 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5235 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 11/21.01 = 0.5235 kW
Answer
Ẇmin = 0.5235 kW
19.Waves, sound & optics
Answer: L = 0.6496 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 343/792 = 0.4331 m
Length
L = nλ/2 = 3·0.4331/2 = 0.6496 m
Answer
L = 0.6496 m
20.Waves, sound & optics
Answer: θa = 33.21 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.