Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 120 km/h sees an obstacle. Her reaction time is 0.8 s, after which the car brakes with a constant deceleration of 5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 120 km/htr = 0.8 sa = −5 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 19 m/s from the edge of a roof 15 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 19 m/sh₀ = 15 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
An 8 kg block slides down a frictionless slope at 20° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 20°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5 kgm2 = 1.5 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 40° above the horizontal towards a wall 64 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 40°x = 64 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is thrown from ground level at 32 m/s and 65° above the horizontal. It lands on the flat roof of a building 28 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 32 m/sθ = 65°hroof = 28 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.4. Find its speed v after it has slid 19 m along the slope.
θ = 35°μ = 0.4d = 19 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 1 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.2) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 1 kgh = 3.5 mL = 2.5 mμ = 0.2k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
An 8 g bullet is fired horizontally into a 3.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 13 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 3.5 kgh = 13 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 5 kg block hanging from light strings 1.6 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 5 kgL = 1.6 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 5 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².
d = 30 mmh = 5 mCd = 0.64g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 6 m. At section 1 the pressure is 190 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 5 °C by removing 2 kW of heat, and rejects heat to the surroundings at 28 °C. Find the rate Q̇H at which it rejects heat.
TL = 5 °CTH = 28 °CQ̇L = 2 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 28 °C, removing heat from the cold space at 3 kW. Find the minimum power input Ẇmin.
TH = 28 °CTL = -18 °CQ̇L = 3 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.8 m long; waves travel on it at 80 m/s. Find the frequency f2 of its harmonic number 2.
v = 80 m/sn = 2L = 0.8 m
f2 = Hz
20.Waves, sound & opticsHard
An object is 5 cm in front of a convex mirror with a radius of curvature of 50 cm. Find the magnification m (negative for an inverted image).
do = 5 cmR = 50 cm
m =
3Solutions
1.Kinematics
Answer: d = 137.8 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Reaction distance
d1 = v₀·tr = 33.33·0.8 = 26.67 m
Braking distance
d2 = v₀²/(2a) = 33.33²/(2·5) = 111.1 m
Total
d = 26.67 + 111.1 = 137.8 m
Answer
d = 137.8 m
2.Kinematics
Answer: t = 4.546 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−15 = 19·t − ½·9.81·t²
4.905·t² − 19·t − 15 = 0
Solve the quadratic
Only the positive root is physical.
t = (19 + √(19² + 2·9.81·15))/9.81 = 4.546 s
Answer
t = 4.546 s
3.Newton’s laws
Answer: a = 3.355 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 40° = 30.64 m/s
t = x/vx = 64/30.64 = 2.089 s
Height at that time
y = 25.71·2.089 − ½·9.81·2.089² = 32.3 m
Answer
y = 32.3 m
The ball is still rising at the wall.
6.Projectile motion
Answer: x = 63.53 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 13.52 m/s, vy = 29 m/s
Time to land on the roof
Larger root: the ball is descending.
28 = 29·t − 4.905·t²
t = (29 + √(29² − 2·9.81·28))/9.81 = 4.697 s
Horizontal distance
x = vx·t = 13.52·4.697 = 63.53 m
Answer
x = 63.53 m
7.Work & energy
Answer: v = 9.575 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·19·(0.5736 − 0.4·0.8192)) = 9.575 m/s
Answer
v = 9.575 m/s
8.Work & energy
Answer: x = 19.81 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(3.5 − 0.2·2.5) = 29.43 J
Maximum compression
½kx² = 29.43 → x = √(2·29.43/1500) = 0.1981 m = 19.81 cm
Answer
x = 19.81 cm
9.Momentum & collisions
Answer: v = 700.3 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.13) = 1.597 m/s
Collision
m·v = (m + M)·V → v = (0.008 + 3.5)·1.597/0.008 = 700.3 m/s
Answer
v = 700.3 m/s
10.Momentum & collisions
Answer: v = 856.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.6·(1 − cos 30°) = 0.2144 m
Speed after impact
V = √(2·9.81·0.2144) = 2.051 m/s
Collision
v = (m + M)·V/m = 5.012·2.051/0.012 = 856.5 m/s
Answer
v = 856.5 m/s
11.Hydrostatic force
Answer: F = 132.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·4.5 = 132.4 kN
Answer
F = 132.4 kN
12.Hydrostatic force
Answer: ycp = 3.111 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 1.5·2³/12 = 1 m⁴
ycp = yc + Ic/(yc·A) = 3 + 1/(3·3) = 3.111 m
Answer
ycp = 3.111 m
13.Continuity & Bernoulli
Answer: Q = 4.481 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·5) = 9.905 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 433.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(300/800)·(433.1/303.1) = 10.72 L
Answer
V2 = 10.72 L
17.Heat engines & refrigerators
Answer: Q̇H = 2.165 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 28 + 273.15 = 301.1 K
TL = 5 + 273.15 = 278.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 2·301.1/278.1 = 2.165 kW
Answer
Q̇H = 2.165 kW
Power input: Ẇ = 0.1654 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5409 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 3/5.547 = 0.5409 kW
Answer
Ẇmin = 0.5409 kW
19.Waves, sound & optics
Answer: f2 = 100 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.8/2 = 0.8 m
Frequency
f = v/λ = 80/0.8 = 100 Hz
Answer
f2 = 100 Hz
20.Waves, sound & optics
Answer: m = 0.8333
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.