Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 15 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 6 m/s². How long does it take the police car to catch up? Find t.
vcar = 15 m/sapolice = 6 m/s²v0,police = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 6 s, then runs at constant speed for 26 s, and finally brakes at 5 m/s² until it stops. Find the total travel time t.
a1 = 1.5 m/s²t1 = 6 st2 = 26 sa3 = −5 m/s²
t = s
3.Newton’s lawsMedium
Masses of 9.5 kg and 4.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 9.5 kgm2 = 4.5 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 115 N pulls the front 10 kg block; the 7 kg block is towed behind. The coefficient of kinetic friction is 0.15 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 7 kgm2 = 10 kgF = 115 Nμ = 0.15g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 50° above the horizontal towards a wall 64 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 50°x = 64 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 28 m/sθ = 45°h = 35 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 30 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.6. Find the stopping distance d.
v = 30 km/hμ = 0.6g = 9.81 m/s²
d = m
8.Work & energyHard
A 10 kg block rests on a rough horizontal table (μ = 0.25). A light string runs from it over a smooth pulley at the edge of the table to a hanging 5 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 2.5 m.
m1 = 10 kgm2 = 5 kgμ = 0.25d = 2.5 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 10 g bullet is fired horizontally into a 1 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 23 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 1 kgh = 23 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 1300 kg car runs into a parked 1200 kg car. The wrecks lock together and skid 20.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.6. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 2 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 350 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 100 mm and a gauge pressure of 70 kPa. The nozzle exit diameter is 30 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 40 °C. It takes in 3300 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 775 °CTL = 40 °CQH = 3300 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 80 kW of heat from a source at 700 °C and rejects heat to the surroundings at 27 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -15 °C and also rejects heat to the surroundings at 27 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 700 °CT0 = 27 °CTL = -15 °CQ̇H = 80 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A small loudspeaker radiates 2 W of sound power equally in all directions. Find the sound intensity level β at 3 m.
P = 2 Wr = 3 mI0 = 10⁻¹² W/m²
β = dB
20.Waves, sound & opticsHard
Light of wavelength 589 nm passes through a single slit 0.08 mm wide. Find the angle θ2 of dark fringe number 2 from the straight-through direction.
λ = 589 nma = 0.08 mmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: t = 5 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·15/6 = 5 s
Answer
t = 5 s
At that moment the police car moves at 2v = 30 m/s.
2.Kinematics
Answer: t = 33.8 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·6 = 9 m/s
Braking time
t3 = v/a3 = 9/5 = 1.8 s
Total time
t = 6 + 26 + 1.8 = 33.8 s
Answer
t = 33.8 s
3.Newton’s laws
Answer: a = 3.504 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (9.5 − 4.5)·9.81/(9.5 + 4.5) = 3.504 m/s²
Answer
a = 3.504 m/s²
4.Newton’s laws
Answer: T = 47.35 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: y = 45.88 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 50° = 25.71 m/s
t = x/vx = 64/25.71 = 2.489 s
Height at that time
y = 30.64·2.489 − ½·9.81·2.489² = 45.88 m
Answer
y = 45.88 m
The ball is still rising at the wall.
6.Projectile motion
Answer: x = 106.2 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 45° = 19.8 m/s
vy = v0·sin θ = 28·sin 45° = 19.8 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 19.8·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (19.8 + √(392 + 686.7))/9.81 = 5.366 s
Horizontal distance
x = vx·t = 19.8·5.366 = 106.2 m
Answer
x = 106.2 m
7.Work & energy
Answer: d = 5.899 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 30/3.6 = 8.333 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 8.333²/(2·0.6·9.81) = 5.899 m
Answer
d = 5.899 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 2.859 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 49.05·2.5 = 122.6 J
μ·m₁g·d = 0.25·98.1·2.5 = 61.31 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 61.31 → v = √(2·61.31/15) = 2.859 m/s
Answer
v = 2.859 m/s
9.Momentum & collisions
Answer: v = 214.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.23) = 2.124 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 1)·2.124/0.01 = 214.6 m/s
Answer
v = 214.6 m/s
10.Momentum & collisions
Answer: v1 = 29.87 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·4 = 78.48 kN
Answer
F = 78.48 kN
12.Hydrostatic force
Answer: F = 132.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1.5/2 = 4.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·4.75·2.25 = 132.1 kN
Answer
F = 132.1 kN
13.Continuity & Bernoulli
Answer: p2 = 341.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 30/100 = 0.3
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·70000/(1000·0.9919)) = 11.88 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 11.88²/(2·9.81) = 7.194 m
Answer
H = 7.194 m
15.Ideal gas law
Answer: P = 1494 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 300/16.04 = 18.7 mol
T = 15 + 273.15 = 288.1 K
Pressure
P = nRT/V = 18.7·8.314·288.1/0.03 = 1494 kPa
Answer
P = 1494 kPa
16.Ideal gas law
Answer: ρ = 2.804 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 70 + 273.15 = 343.1 K
Density
ρ = 250·32/(8.314·343.1) = 2.804 kg/m³
Answer
ρ = 2.804 kg/m³
17.Heat engines & refrigerators
Answer: Wmax = 2314 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/1048 = 70.12 %
Maximum work
Wmax = ηmax·QH = 0.7012·3300 = 2314 kJ
Answer
Wmax = 2314 kJ
18.Heat engines & refrigerators
Answer: Q̇L = 340.1 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
T0 = 27 + 273.15 = 300.1 K
TL = -15 + 273.15 = 258.1 K
Engine work
η = 1 − 300.1/973.1 = 0.6916
Ẇ = 0.6916·80 = 55.33 kW
Heat removed by the refrigerator
COPR = 258.1/(300.1 − 258.1) = 6.146
Q̇L = 6.146·55.33 = 340.1 kW
Answer
Q̇L = 340.1 kW
19.Waves, sound & optics
Answer: β = 102.5 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity
I = P/(4πr²) = 0.01768 W/m²
Level
β = 10·log₁₀(0.01768/10⁻¹²) = 102.5 dB
Answer
β = 102.5 dB
20.Waves, sound & optics
Answer: θ2 = 0.8437 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …