Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
v₀ = 100 km/ha = −3 m/s²v = 0
t = s
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 2.4 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 2.4 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 12 kg block slides down a frictionless slope at 35° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 12 kgθ = 35°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 35° with a speed of 4 m/s. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 4 m/sθ = 35°μ = 0.2g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 15° above the horizontal and lands 90 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 15°R = 90 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 10 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 14 m/sθ = 60°h = 10 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 1 kg block slides 7 m down a slope at 30° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 1 kgθ = 30°μ = 0.3d = 7 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 1.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.25) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 1.5 mL = 3 mμ = 0.25k = 5000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 5 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 5 kgm2 = 1 kgv1 = 2 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 2000 kg car travelling east at 15 m/s collides with a 1300 kg car travelling north at 25 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 2000 kgv1 = 15 m/s (E)m2 = 1300 kgv2 = 25 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 310 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 80 mm, throat 40 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 60 mm. The discharge coefficient is 0.98. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 300 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 300 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 35 °C, removing heat from the cold space at 4 kW. Find the highest possible coefficient of performance COPmax.
TH = 35 °CTL = -18 °CQ̇L = 4 kW
COPmax =
19.Waves, sound & opticsMedium
A small loudspeaker radiates 2 W of sound power equally in all directions. Find the sound intensity level β at 8 m.
P = 2 Wr = 8 mI0 = 10⁻¹² W/m²
β = dB
20.Waves, sound & opticsHard
Two thin lenses share an axis, 60 cm apart: lens 1 with f₁ = 12 cm and lens 2 with f₂ = −10 cm. An object stands 18 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 12 cmf2 = −10 cms = 60 cmdo = 18 cm
di2 = cm
3Solutions
1.Kinematics
Answer: t = 9.259 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 27.78/3 = 9.259 s
Answer
t = 9.259 s
2.Kinematics
Answer: d = 26.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(2.4 − t₁)
4.905·t₁² + 343·t₁ − 823.2 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·823.2))/(2·4.905) = 2.323 s
Depth
d = ½·9.81·2.323² = 26.47 m
Answer
d = 26.47 m
3.Newton’s laws
Answer: a = 5.627 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 35° + 0.2·cos 35°) = 7.234 m/s²
Distance
d = v₀²/(2a) = 4²/(2·7.234) = 1.106 m
Answer
d = 1.106 m
5.Projectile motion
Answer: v0 = 42.02 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·90/sin 30°) = 42.02 m/s
Answer
v0 = 42.02 m/s
6.Projectile motion
Answer: t = 3.124 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 60° = 7 m/s
vy = v0·sin θ = 14·sin 60° = 12.12 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 10 + 12.12·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (12.12 + √(147 + 196.2))/9.81 = 3.124 s
Answer
t = 3.124 s
7.Work & energy
Answer: Wf = 17.84 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 9.81·0.866 = 8.496 N
F = μN = 0.3·8.496 = 2.549 N
Work against friction
Wf = F·d = 2.549·7 = 17.84 J
Answer
Wf = 17.84 J
8.Work & energy
Answer: v = 3.836 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(1.5 − 0.25·3) = 3.679 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·0.75) = 3.836 m/s
Answer
v = 3.836 m/s
9.Momentum & collisions
Answer: v′2 = 3.333 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 1)/(5 + 1)·2 = 1.333 m/s
v′2 = 2·5/(5 + 1)·2 = 3.333 m/s
Answer
v′2 = 3.333 m/s
10.Momentum & collisions
Answer: v′ = 13.4 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.75·3 = 110.4 kN
Answer
F = 110.4 kN
12.Hydrostatic force
Answer: F = 63.13 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.25·2.25 = 63.13 kN
Answer
F = 63.13 kN
13.Continuity & Bernoulli
Answer: p2 = 287 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.06 = 7416 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/573.1 = 51.47 %
Answer
ηmax = 51.47 %
18.Heat engines & refrigerators
Answer: COPmax = 4.814
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity
I = P/(4πr²) = 0.002487 W/m²
Level
β = 10·log₁₀(0.002487/10⁻¹²) = 93.96 dB
Answer
β = 93.96 dB
20.Waves, sound & optics
Answer: di2 = −7.059 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.