Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 120 km/h brakes with a constant deceleration of 8 m/s² until it stops. Find the braking distance s.
v₀ = 120 km/ha = −8 m/s²v = 0
s = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 40 m/s² for 2.5 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 40 m/s²t1 = 2.5 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
Masses of 10 kg and 5.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 10 kgm2 = 5.5 kgg = 9.81 m/s²
T = N
4.Newton’s lawsHard
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 2 kgm2 = 4.5 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 16 m/sθ = 70°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 25° above horizontal from the top of a 60 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 15 m/sθ = 25°h = 60 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 2.5 kg block slides 9 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
m = 2.5 kgθ = 20°μ = 0.2d = 9 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4.5 m long (μ = 0.15) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 2.5 mL = 4.5 mμ = 0.15k = 1500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1700 kg car moving at 17 m/s runs into a stationary 1700 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1700 kgv1 = 17 m/sm2 = 1700 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 27 m/s and bounces straight back at 12 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.2 kgvin = 27 m/svout = 12 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 15 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 1 m. At section 1 the pressure is 250 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 35 °C. It takes in 2000 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 775 °CTL = 35 °CQH = 2000 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 4600 kJ of heat from a reservoir at 600 °C, produces 1518 kJ of work and rejects the rest to a reservoir at 15 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 600 °CTL = 15 °CQH = 4600 kJW = 1518 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.65 m long; waves travel on it at 100 m/s. Find the frequency f1 of its fundamental (first harmonic).
v = 100 m/sn = 1L = 0.65 m
f1 = Hz
20.Waves, sound & opticsHard
A diffraction grating has 100 lines per millimetre. Light of wavelength 589 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 100 mm⁻¹λ = 589 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 69.44 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 33.33²/(2·8) = 69.44 m
Answer
s = 69.44 m
2.Kinematics
Answer: hmax = 634.7 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 40·2.5 = 100 m/s
h₁ = ½·40·2.5² = 125 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 100²/(2·9.81) = 509.7 m
hmax = 125 + 509.7 = 634.7 m
Answer
hmax = 634.7 m
3.Newton’s laws
Answer: T = 69.62 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (10 − 5.5)·9.81/(10 + 5.5) = 2.848 m/s²
Tension from the lighter mass
T − m2·g = m2·a → T = 5.5·(9.81 + 2.848) = 69.62 N
Answer
T = 69.62 N
4.Newton’s laws
Answer: a = 6.188 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 70° = 5.472 m/s
vy = v0·sin θ = 16·sin 70° = 15.04 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·15.04/9.81 = 3.065 s
Horizontal distance
x = vx·t = 5.472·3.065 = 16.77 m
Answer
x = 16.77 m
6.Projectile motion
Answer: t = 4.203 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 15·cos 25° = 13.59 m/s
vy = v0·sin θ = 15·sin 25° = 6.339 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 60 + 6.339·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (6.339 + √(40.19 + 1177))/9.81 = 4.203 s
Answer
t = 4.203 s
7.Work & energy
Answer: Wf = 41.48 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.9397 = 23.05 N
F = μN = 0.2·23.05 = 4.609 N
Work against friction
Wf = F·d = 4.609·9 = 41.48 J
Answer
Wf = 41.48 J
8.Work & energy
Answer: v = 5.984 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(2.5 − 0.15·4.5) = 8.952 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·1.825) = 5.984 m/s
Answer
v = 5.984 m/s
9.Momentum & collisions
Answer: ΔK/K = 50 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1700·17/3400 = 8.5 m/s
Kinetic energy before and after
Kbefore = ½·1700·17² = 245650 J
Kafter = ½·3400·8.5² = 122825 J
Fraction lost
ΔK/K = 122825/245650 = 50 %
Answer
ΔK/K = 50 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 390 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(12 + 27) = 7.8 N·s
Average force
Favg = J/Δt = 7.8/0.02 = 390 N
Answer
Favg = 390 N
11.Hydrostatic force
Answer: F = 193.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·3.75 = 193.1 kN
Answer
F = 193.1 kN
12.Hydrostatic force
Answer: ycp = 3.308 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.25·2.25 = 63.13 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/1048 = 70.6 %
Maximum work
Wmax = ηmax·QH = 0.706·2000 = 1412 kJ
Answer
Wmax = 1412 kJ
18.Heat engines & refrigerators
Answer: Sgen = 5.428 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 4600 − 1518 = 3082 kJ
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 15 + 273.15 = 288.1 K
Entropy changes of the reservoirs
ΔSH = −4600/873.1 = −5.268 kJ/K
ΔSL = 3082/288.1 = 10.7 kJ/K
Sgen = 10.7 − 5.268 = 5.428 kJ/K
Answer
Sgen = 5.428 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f1 = 76.92 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.65/1 = 1.3 m
Frequency
f = v/λ = 100/1.3 = 76.92 Hz
Answer
f1 = 76.92 Hz
20.Waves, sound & optics
Answer: mmax = 16
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …