Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 120 km/h sees an obstacle. Her reaction time is 0.9 s, after which the car brakes with a constant deceleration of 4 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 120 km/htr = 0.9 sa = −4 m/s²
d = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 2.6 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 2.6 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
An 8 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 30°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 10 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 10 m/sθ = 25°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 14 m/sθ = 50°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 29 m/s and 45° above the horizontal from the top of a 55 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 29 m/sθ = 45°h = 55 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A car travelling at 110 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 110 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 2 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.15) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 3 mL = 3.5 mμ = 0.15k = 800 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3.5 kg glider moving at 6 m/s makes a perfectly elastic head-on collision with a 3 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 3.5 kgm2 = 3 kgv1 = 6 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 27 m/s and bounces straight back at 11 m/s. The contact lasts 50 ms. Find the average force Favg of the wall on the ball.
m = 0.2 kgvin = 27 m/svout = 11 m/sΔt = 50 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 2 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 1 mH = 2 mb = 1 mρ = 1025 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 50 mm. The water level is kept 1.5 m above the orifice and the discharge coefficient is 0.6. Find the flow rate Q. Use g = 9.81 m/s².
d = 50 mmh = 1.5 mCd = 0.6g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 2 m. At section 1 the pressure is 180 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 3900 kJ of heat from a reservoir at 300 °C and rejects 1961 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 300 °CQH = 3900 kJQL = 1961 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat engine takes in 2900 kJ of heat from a reservoir at 750 °C, produces 1015 kJ of work and rejects the rest to a reservoir at 40 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 750 °CTL = 40 °CQH = 2900 kJW = 1015 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object stands 25 cm in front of a thin converging lens with a focal length of 30 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 25 cmf = 30 cm
di = cm
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.62 and a cladding with n₂ = 1.54. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.62n2 = 1.54n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: d = 168.9 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Reaction distance
d1 = v₀·tr = 33.33·0.9 = 30 m
Braking distance
d2 = v₀²/(2a) = 33.33²/(2·4) = 138.9 m
Total
d = 30 + 138.9 = 168.9 m
Answer
d = 168.9 m
2.Kinematics
Answer: d = 30.9 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(2.6 − t₁)
4.905·t₁² + 343·t₁ − 891.8 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·891.8))/(2·4.905) = 2.51 s
Depth
d = ½·9.81·2.51² = 30.9 m
Answer
d = 30.9 m
3.Newton’s laws
Answer: a = 2.781 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.1·cos 25°) = 5.035 m/s²
Distance
d = v₀²/(2a) = 10²/(2·5.035) = 9.931 m
Answer
d = 9.931 m
5.Projectile motion
Answer: t = 2.186 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 50° = 8.999 m/s
vy = v0·sin θ = 14·sin 50° = 10.72 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·10.72/9.81 = 2.186 s
Answer
t = 2.186 s
6.Projectile motion
Answer: v = 43.82 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 29·cos 45° = 20.51 m/s
vy0 = 29·sin 45° = 20.51 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(20.51² + 2·9.81·55) = 38.72 m/s
Impact speed
v = √(20.51² + 38.72²) = 43.82 m/s
Answer
v = 43.82 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: d = 67.98 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 110/3.6 = 30.56 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 30.56²/(2·0.7·9.81) = 67.98 m
Answer
d = 67.98 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 34.84 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(3 − 0.15·3.5) = 48.56 J
Maximum compression
½kx² = 48.56 → x = √(2·48.56/800) = 0.3484 m = 34.84 cm
Answer
x = 34.84 cm
9.Momentum & collisions
Answer: v′1 = 0.4615 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 3)/(3.5 + 3)·6 = 0.4615 m/s
v′2 = 2·3.5/(3.5 + 3)·6 = 6.462 m/s
Answer
v′1 = 0.4615 m/s
10.Momentum & collisions
Answer: Favg = 152 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(11 + 27) = 7.6 N·s
Average force
Favg = J/Δt = 7.6/0.05 = 152 N
Answer
Favg = 152 N
11.Hydrostatic force
Answer: F = 235.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·6 = 235.4 kN
Answer
F = 235.4 kN
12.Hydrostatic force
Answer: ycp = 2.167 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2·2 = 40.22 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 1·2³/12 = 0.6667 m⁴
ycp = yc + Ic/(yc·A) = 2 + 0.6667/(2·2) = 2.167 m
Answer
ycp = 2.167 m
13.Continuity & Bernoulli
Answer: Q = 6.391 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·1.5) = 5.425 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 493.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(350/450)·(493.1/298.1) = 25.73 L
Answer
V2 = 25.73 L
17.Heat engines & refrigerators
Answer: TL = 15.04 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 300 + 273.15 = 573.1 K
Reversible heat ratio
TL = TH·QL/QH = 573.1·1961/3900 = 288.2 K = 15.04 °C
Answer
TL = 15.04 °C
18.Heat engines & refrigerators
Answer: Sgen = 3.185 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 2900 − 1015 = 1885 kJ
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 40 + 273.15 = 313.1 K
Entropy changes of the reservoirs
ΔSH = −2900/1023 = −2.834 kJ/K
ΔSL = 1885/313.1 = 6.019 kJ/K
Sgen = 6.019 − 2.834 = 3.185 kJ/K
Answer
Sgen = 3.185 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: di = −150 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/30 − 1/25
di = −150 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −150 cm
20.Waves, sound & optics
Answer: θa = 30.18 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.