Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 120 km/h sees an obstacle. Her reaction time is 1.4 s, after which the car brakes with a constant deceleration of 7.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 120 km/htr = 1.4 sa = −7.5 m/s²
d = m
2.KinematicsHard
Ball A is dropped from rest from a height of 35 m. At the same instant ball B is thrown straight up from the ground directly below at 17 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 35 mv0B = 17 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 2.5 m/s and comes to rest after 0.8 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 2.5 m/sd = 0.8 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 15° with a speed of 11.5 m/s. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 11.5 m/sθ = 15°μ = 0.25g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 24 m/sθ = 35°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 24 m/s and 55° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 24 m/sθ = 55°h = 50 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A car travelling at 120 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 120 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 2 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.1) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 4 mL = 5 mμ = 0.1k = 1000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
An 8 kg projectile moving horizontally at 19 m/s explodes into two fragments that move along the same line. The 1 kg fragment continues forwards at 41 m/s. Find the velocity v′2 of the 7 kg fragment (positive in the original direction).
M = 8 kgu = 19 m/sm1 = 1 kgv′1 = 41 m/sm2 = 7 kg
v′2 = m/s
10.Momentum & collisionsHard
A 1600 kg car runs into a parked 2000 kg car. The wrecks lock together and skid 10.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.75. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows at 40 L/s through a horizontal pipe that narrows from 200 mm to 100 mm. The pressure in the narrow section is 130 kPa. Ignoring losses, find the pressure p1 in the wide section.
A hose with an inner diameter of 20 mm siphons water from an open tank. The highest point C of the hose is 1.5 m above the water surface, and the outlet (open to the air) is 4 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 20 mmzC = +1.5 mz2 = −4 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 320 g of CO₂ occupy at 350 kPa and 55 °C? Treat it as an ideal gas.
A heat engine works between a hot reservoir at 425 °C and a cold reservoir at 25 °C. It takes in 1300 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 425 °CTL = 25 °CQH = 1300 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 30 °C, removing heat from the cold space at 4 kW. Find the highest possible coefficient of performance COPmax.
TH = 30 °CTL = -18 °CQ̇L = 4 kW
COPmax =
19.Waves, sound & opticsMedium
An object stands 30 cm in front of a thin diverging lens with a focal length of 12 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 30 cmf = −12 cm
di = cm
20.Waves, sound & opticsHard
An object is 15 cm in front of a convex mirror with a radius of curvature of 20 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 15 cmR = 20 cm
di = cm
3Solutions
1.Kinematics
Answer: d = 120.7 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Reaction distance
d1 = v₀·tr = 33.33·1.4 = 46.67 m
Braking distance
d2 = v₀²/(2a) = 33.33²/(2·7.5) = 74.07 m
Total
d = 46.67 + 74.07 = 120.7 m
Answer
d = 120.7 m
2.Kinematics
Answer: y = 14.21 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
35 − ½g·t² = 17·t − ½g·t² → t = 35/17 = 2.059 s
Meeting height
y = 17·2.059 − ½·9.81·2.059² = 14.21 m
Answer
y = 14.21 m
3.Newton’s laws
Answer: μ = 0.3982
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 2.5²/(2·0.8) = 3.906 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 3.906/9.81 = 0.3982
Answer
μ = 0.3982
4.Newton’s laws
Answer: d = 13.47 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 15° + 0.25·cos 15°) = 4.908 m/s²
Distance
d = v₀²/(2a) = 11.5²/(2·4.908) = 13.47 m
Answer
d = 13.47 m
5.Projectile motion
Answer: x = 55.17 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 35° = 19.66 m/s
vy = v0·sin θ = 24·sin 35° = 13.77 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13.77/9.81 = 2.806 s
Horizontal distance
x = vx·t = 19.66·2.806 = 55.17 m
Answer
x = 55.17 m
6.Projectile motion
Answer: α = 69.58 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 24·cos 55° = 13.77 m/s
vy0 = 24·sin 55° = 19.66 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(19.66² + 2·9.81·50) = 36.98 m/s
Impact angle
tan α = vy/vx = 36.98/13.77 → α = 69.58°
Answer
α = 69.58°
7.Work & energy
Answer: d = 80.9 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 120/3.6 = 33.33 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 33.33²/(2·0.7·9.81) = 80.9 m
Answer
d = 80.9 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 37.06 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(4 − 0.1·5) = 68.67 J
Maximum compression
½kx² = 68.67 → x = √(2·68.67/1000) = 0.3706 m = 37.06 cm
Answer
x = 37.06 cm
9.Momentum & collisions
Answer: v′2 = 15.86 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 8·19 = 152 kg·m/s
Momentum after
152 = 1·41 + 7·v′2
v′2 = (152 − 41)/7 = 15.86 m/s
Answer
v′2 = 15.86 m/s
10.Momentum & collisions
Answer: v1 = 27.97 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 425 + 273.15 = 698.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/698.1 = 57.29 %
Maximum work
Wmax = ηmax·QH = 0.5729·1300 = 744.8 kJ
Answer
Wmax = 744.8 kJ
18.Heat engines & refrigerators
Answer: COPmax = 5.316
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−12) − 1/30
di = −8.571 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −8.571 cm
20.Waves, sound & optics
Answer: di = −6 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.