Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 54 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. Find the braking distance s.
v₀ = 54 km/ha = −7.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 6 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 6 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 10 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 10 kgθ = 40°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1 kgm2 = 1 kgμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 32 m/s and must land 55 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 32 m/sR = 55 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 23 m/s and 50° above the horizontal from the top of a 40 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 23 m/sθ = 50°h = 40 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A car travelling at 100 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 100 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 20 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 140 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 3 m up the slope.
A 15 g bullet is fired horizontally into a 2.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 20 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 2.5 kgh = 20 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 12 m/s and bounces straight back at 17 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.5 kgvin = 12 m/svout = 17 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 150 mm to 50 mm. In the wide section the pressure is 310 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 60 kPa. Water leaves through an opening with a diameter of 50 mm, 4 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A reversible refrigerator keeps a cold room at 0 °C by removing 4.5 kW of heat, and rejects heat to the surroundings at 30 °C. Find the rate Q̇H at which it rejects heat.
TL = 0 °CTH = 30 °CQ̇L = 4.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat engine takes in 500 kJ of heat from a reservoir at 550 °C, produces 220 kJ of work and rejects the rest to a reservoir at 35 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 550 °CTL = 35 °CQH = 500 kJW = 220 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A pipe closed at one end is 0.8 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 0.8 m
f5 = Hz
20.Waves, sound & opticsHard
Light of wavelength 600 nm falls at right angles on a grating with 400 lines per millimetre. Find the angle θ3 of the order-3 maximum.
N = 400 mm⁻¹λ = 600 nmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: s = 15 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 54/3.6 = 15 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 15²/(2·7.5) = 15 m
Answer
s = 15 m
2.Kinematics
Answer: t = 2.721 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 6·t − ½·9.81·t²
4.905·t² − 6·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (6 + √(6² + 2·9.81·20))/9.81 = 2.721 s
Answer
t = 2.721 s
3.Newton’s laws
Answer: a = 5.179 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·55/32² = 0.5269
Angle
2θ = 31.8° → θ = 15.9°
Answer
θ = 15.9°
The other solution is 90° − θ = 74.1°.
6.Projectile motion
Answer: v = 36.25 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 23·cos 50° = 14.78 m/s
vy0 = 23·sin 50° = 17.62 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(17.62² + 2·9.81·40) = 33.09 m/s
Impact speed
v = √(14.78² + 33.09²) = 36.25 m/s
Answer
v = 36.25 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: d = 56.18 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 100/3.6 = 27.78 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 27.78²/(2·0.7·9.81) = 56.18 m
Answer
d = 56.18 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 4.042 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 20·9.81 = 196.2 N
mg·sin θ = 67.1 N
μ·mg·cos θ = 18.44 N
Work–energy
½mv² = (140 − 85.54)·3 = 163.4 J
v = √(2·163.4/20) = 4.042 m/s
Answer
v = 4.042 m/s
9.Momentum & collisions
Answer: v = 332.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.2) = 1.981 m/s
Collision
m·v = (m + M)·V → v = (0.015 + 2.5)·1.981/0.015 = 332.1 m/s
Answer
v = 332.1 m/s
10.Momentum & collisions
Answer: Favg = 362.5 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(17 + 12) = 14.5 N·s
Average force
Favg = J/Δt = 14.5/0.04 = 362.5 N
Answer
Favg = 362.5 N
11.Hydrostatic force
Answer: F = 79.71 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·2.5 = 79.71 kN
Answer
F = 79.71 kN
12.Hydrostatic force
Answer: ycp = 2.481 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.25·7.5 = 169.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 323.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(200/650)·(323.1/293.1) = 6.784 L
Answer
V2 = 6.784 L
17.Heat engines & refrigerators
Answer: Q̇H = 4.994 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 30 + 273.15 = 303.1 K
TL = 0 + 273.15 = 273.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 4.5·303.1/273.1 = 4.994 kW
Answer
Q̇H = 4.994 kW
Power input: Ẇ = 0.4942 kW.
18.Heat engines & refrigerators
Answer: Sgen = 0.3012 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 500 − 220 = 280 kJ
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 35 + 273.15 = 308.1 K
Entropy changes of the reservoirs
ΔSH = −500/823.1 = −0.6074 kJ/K
ΔSL = 280/308.1 = 0.9086 kJ/K
Sgen = 0.9086 − 0.6074 = 0.3012 kJ/K
Answer
Sgen = 0.3012 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f5 = 535.9 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·0.8/5 = 0.64 m
Frequency
f = v/λ = 343/0.64 = 535.9 Hz
Answer
f5 = 535.9 Hz
20.Waves, sound & optics
Answer: θ3 = 46.05 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …