Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 60 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 60 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 10 s, then runs at constant speed for 29 s, and finally brakes at 4 m/s² until it stops. Find the total travel time t.
a1 = 1.5 m/s²t1 = 10 st2 = 29 sa3 = −4 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 10.5 m/s and comes to rest after 37 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 10.5 m/sd = 37 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 10 kg block on a ramp at 30° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 8.5 kg mass. The hanging mass moves down. The ramp is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 10 kgm2 = 8.5 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 12 m/s and 25° above the horizontal towards a wall 8 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 12 m/sθ = 25°x = 8 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 10 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 32 m/sθ = 60°h = 10 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 60 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.6. Find the stopping distance d.
v = 60 km/hμ = 0.6g = 9.81 m/s²
d = m
8.Work & energyHard
A 2 kg block is released from rest at height 1.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.25) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 1.5 mL = 2.5 mμ = 0.25k = 1000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1.5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 1.5 kgm2 = 0.5 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.15 kg ball hits a wall at 29 m/s and bounces straight back at 17 m/s. The contact lasts 50 ms. Find the average force Favg of the wall on the ball.
m = 0.15 kgvin = 29 m/svout = 17 m/sΔt = 50 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows at 33 L/s through a horizontal pipe that narrows from 200 mm to 100 mm. The pressure in the narrow section is 160 kPa. Ignoring losses, find the pressure p1 in the wide section.
A hose with an inner diameter of 40 mm siphons water from an open tank. The highest point C of the hose is 1 m above the water surface, and the outlet (open to the air) is 1 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 40 mmzC = +1 mz2 = −1 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
A tank of 30 L contains 190 g of He at 80 °C. Treat it as an ideal gas and find the pressure P.
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 40 °C. It takes in 2400 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 775 °CTL = 40 °CQH = 2400 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 5 °C in a kitchen at 30 °C, removing heat from the cold space at 1 kW. Find the highest possible coefficient of performance COPmax.
TH = 30 °CTL = 5 °CQ̇L = 1 kW
COPmax =
19.Waves, sound & opticsMedium
An object 4 cm tall stands 10 cm in front of a thin converging lens with a focal length of 20 cm. Find the image height hi (negative for an inverted image).
ho = 4 cmdo = 10 cmf = 20 cm
hi = cm
20.Waves, sound & opticsHard
Light of wavelength 650 nm passes through a single slit 0.08 mm wide. Find the angle θ3 of dark fringe number 3 from the straight-through direction.
λ = 650 nma = 0.08 mmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: s = 46.3 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 16.67²/(2·3) = 46.3 m
Answer
s = 46.3 m
2.Kinematics
Answer: t = 42.75 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·10 = 15 m/s
Braking time
t3 = v/a3 = 15/4 = 3.75 s
Total time
t = 10 + 29 + 3.75 = 42.75 s
Answer
t = 42.75 s
3.Newton’s laws
Answer: μ = 0.1519
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 10.5²/(2·37) = 1.49 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.49/9.81 = 0.1519
Answer
μ = 0.1519
4.Newton’s laws
Answer: a = 1.856 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 83.39 N
m₁·g·sin θ = 49.05 N
μ·m₁·g·cos θ = 0 N
Acceleration of the system
a = (83.39 − 49.05 − 0)/18.5 = 1.856 m/s²
Answer
a = 1.856 m/s²
5.Projectile motion
Answer: y = 1.076 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 12·cos 25° = 10.88 m/s
t = x/vx = 8/10.88 = 0.7356 s
Height at that time
y = 5.071·0.7356 − ½·9.81·0.7356² = 1.076 m
Answer
y = 1.076 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: t = 5.99 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 32·cos 60° = 16 m/s
vy = v0·sin θ = 32·sin 60° = 27.71 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 10 + 27.71·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (27.71 + √(768 + 196.2))/9.81 = 5.99 s
Answer
t = 5.99 s
7.Work & energy
Answer: d = 23.6 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 60/3.6 = 16.67 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 16.67²/(2·0.6·9.81) = 23.6 m
Answer
d = 23.6 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 18.53 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(1.5 − 0.25·2.5) = 17.17 J
Maximum compression
½kx² = 17.17 → x = √(2·17.17/1000) = 0.1853 m = 18.53 cm
Answer
x = 18.53 cm
9.Momentum & collisions
Answer: v′2 = 16.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 0.5)/(1.5 + 0.5)·11 = 5.5 m/s
v′2 = 2·1.5/(1.5 + 0.5)·11 = 16.5 m/s
Answer
v′2 = 16.5 m/s
10.Momentum & collisions
Answer: Favg = 138 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.15·(17 + 29) = 6.9 N·s
Average force
Favg = J/Δt = 6.9/0.05 = 138 N
Answer
Favg = 138 N
11.Hydrostatic force
Answer: F = 29.43 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·2 = 29.43 kN
Answer
F = 29.43 kN
12.Hydrostatic force
Answer: F = 185.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2/2 = 5 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·5·3 = 185.4 kN
Answer
F = 185.4 kN
13.Continuity & Bernoulli
Answer: p1 = 168.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/1048 = 70.12 %
Maximum work
Wmax = ηmax·QH = 0.7012·2400 = 1683 kJ
Answer
Wmax = 1683 kJ
18.Heat engines & refrigerators
Answer: COPmax = 11.13
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/20 − 1/10
di = −20 cm
Magnification and height
m = −(−20)/10 = 2
hi = 2·4 = 8 cm
Answer
hi = 8 cm
20.Waves, sound & optics
Answer: θ3 = 1.397 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …