Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 60 km/h brakes with a constant deceleration of 7 m/s² until it stops. Find the braking distance s.
v₀ = 60 km/ha = −7 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 5 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 11 m/sh₀ = 5 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 12 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 12 kgθ = 35°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1 kgm2 = 1.5 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 14 m/sθ = 70°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 37 m/s and 70° above the horizontal. It lands on the flat roof of a building 19 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 37 m/sθ = 70°hroof = 19 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 50 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 50 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 2 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.3) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 5 mL = 1 mμ = 0.3k = 2000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 3 kgm2 = 4 kgv1 = 11 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
An 8 g bullet is fired horizontally into a 1 kg block hanging from light strings 1.8 m long, and stays in it. The strings swing out to a largest angle of 40° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 1 kgL = 1.8 mθ = 40°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 220 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 150 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 250 mm. The discharge coefficient is 0.98. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 3900 kJ of heat from a reservoir at 350 °C and rejects 2054 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 350 °CQH = 3900 kJQL = 2054 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 0 °C outside, delivering 8 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 0 °CQ̇H = 8 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
Light travels in water (n = 1.33) towards a flat boundary with air (n = 1.00). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.33n2 = 1.00
θc = °
20.Waves, sound & opticsHard
Two thin lenses share an axis, 15 cm apart: lens 1 with f₁ = 5 cm and lens 2 with f₂ = −20 cm. An object stands 25 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 5 cmf2 = −20 cms = 15 cmdo = 25 cm
di2 = cm
3Solutions
1.Kinematics
Answer: s = 19.84 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 16.67²/(2·7) = 19.84 m
Answer
s = 19.84 m
2.Kinematics
Answer: hmax = 11.17 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 11²/(2·9.81) = 6.167 m
Height above the ground
hmax = 5 + 6.167 = 11.17 m
Answer
hmax = 11.17 m
3.Newton’s laws
Answer: a = 4.02 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 70° = 4.788 m/s
vy = v0·sin θ = 14·sin 70° = 13.16 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13.16/9.81 = 2.682 s
Horizontal distance
x = vx·t = 4.788·2.682 = 12.84 m
Answer
x = 12.84 m
6.Projectile motion
Answer: x = 82.15 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 12.65 m/s, vy = 34.77 m/s
Time to land on the roof
Larger root: the ball is descending.
19 = 34.77·t − 4.905·t²
t = (34.77 + √(34.77² − 2·9.81·19))/9.81 = 6.492 s
Horizontal distance
x = vx·t = 12.65·6.492 = 82.15 m
Answer
x = 82.15 m
7.Work & energy
Answer: d = 14.05 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 50/3.6 = 13.89 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 13.89²/(2·0.7·9.81) = 14.05 m
Answer
d = 14.05 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 30.37 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(5 − 0.3·1) = 92.21 J
Maximum compression
½kx² = 92.21 → x = √(2·92.21/2000) = 0.3037 m = 30.37 cm
Answer
x = 30.37 cm
9.Momentum & collisions
Answer: v′1 = −1.571 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 4)/(3 + 4)·11 = −1.571 m/s
v′2 = 2·3/(3 + 4)·11 = 9.429 m/s
Answer
v′1 = −1.571 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 362.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.8·(1 − cos 40°) = 0.4211 m
Speed after impact
V = √(2·9.81·0.4211) = 2.874 m/s
Collision
v = (m + M)·V/m = 1.008·2.874/0.008 = 362.2 m/s
Answer
v = 362.2 m/s
11.Hydrostatic force
Answer: F = 49.05 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2/2 = 2.5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·2 = 49.05 kN
Answer
F = 49.05 kN
12.Hydrostatic force
Answer: ycp = 2.939 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2.75·2.5 = 59.35 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.25 = 30902 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 350 + 273.15 = 623.1 K
Reversible heat ratio
TL = TH·QL/QH = 623.1·2054/3900 = 328.2 K = 55.04 °C
Answer
TL = 55.04 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5963 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 8/13.42 = 0.5963 kW
Answer
Ẇmin = 0.5963 kW
19.Waves, sound & optics
Answer: θc = 48.75 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.00/1.33 = 0.7519
Critical angle
θc = arcsin(0.7519) = 48.75°
Answer
θc = 48.75°
20.Waves, sound & optics
Answer: di2 = −6.087 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.