Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 120 km/h brakes with a constant deceleration of 8 m/s² until it stops. How long does braking take? Find t.
v₀ = 120 km/ha = −8 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 14 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 14 m/sh₀ = 10 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 30 kg sled is pulled across level snow by a rope at 25° above the horizontal with a force of 80 N. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 30 kgF = 80 Nθ = 25°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 15° with a speed of 7 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 7 m/sθ = 15°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 18 m/sθ = 50°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 35° above horizontal from the top of a 25 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 11 m/sθ = 35°h = 25 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 120 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.8. Find the stopping distance d.
v = 120 km/hμ = 0.8g = 9.81 m/s²
d = m
8.Work & energyHard
An 8 kg block starts from rest at the bottom of a 15° slope and is pulled up the slope by a constant force of 90 N parallel to the slope. The coefficient of kinetic friction is 0.3. Find the speed v of the block after it has moved 7 m up the slope.
A 4 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4 kgm2 = 1.5 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.35 kg ball hits a wall at 30 m/s and bounces straight back at 10 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.35 kgvin = 30 m/svout = 10 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 150 mm to 75 mm. In the wide section the pressure is 250 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 5 m. At section 1 the pressure is 110 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at -10 °C by removing 5.5 kW of heat, and rejects heat to the surroundings at 40 °C. Find the rate Q̇H at which it rejects heat.
TL = -10 °CTH = 40 °CQ̇L = 5.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 70 kW of heat from a source at 750 °C and rejects heat to the surroundings at 27 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -5 °C and also rejects heat to the surroundings at 27 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 750 °CT0 = 27 °CTL = -5 °CQ̇H = 70 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A small loudspeaker radiates 0.2 W of sound power equally in all directions. Find the sound intensity level β at 2 m.
P = 0.2 Wr = 2 mI0 = 10⁻¹² W/m²
β = dB
20.Waves, sound & opticsHard
An object is 50 cm in front of a concave mirror with a radius of curvature of 30 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 50 cmR = 30 cm
di = cm
3Solutions
1.Kinematics
Answer: t = 4.167 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 33.33/8 = 4.167 s
Answer
t = 4.167 s
2.Kinematics
Answer: t = 3.446 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−10 = 14·t − ½·9.81·t²
4.905·t² − 14·t − 10 = 0
Solve the quadratic
Only the positive root is physical.
t = (14 + √(14² + 2·9.81·10))/9.81 = 3.446 s
Answer
t = 3.446 s
3.Newton’s laws
Answer: a = 1.549 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 294.3 − 80·sin 25° = 260.5 N
Horizontal forces
m·a = F·cos θ − μ·N = 72.5 − 26.05
a = 46.46/30 = 1.549 m/s²
Answer
a = 1.549 m/s²
4.Newton’s laws
Answer: d = 7.027 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 15° + 0.1·cos 15°) = 3.487 m/s²
Distance
d = v₀²/(2a) = 7²/(2·3.487) = 7.027 m
Answer
d = 7.027 m
5.Projectile motion
Answer: H = 9.691 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 50° = 11.57 m/s
vy = v0·sin θ = 18·sin 50° = 13.79 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 13.79²/(2·9.81) = 9.691 m
Answer
H = 9.691 m
6.Projectile motion
Answer: x = 26.95 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 11·cos 35° = 9.011 m/s
vy = v0·sin θ = 11·sin 35° = 6.309 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 25 + 6.309·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (6.309 + √(39.81 + 490.5))/9.81 = 2.991 s
Horizontal distance
x = vx·t = 9.011·2.991 = 26.95 m
Answer
x = 26.95 m
7.Work & energy
Answer: d = 70.79 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 120/3.6 = 33.33 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 33.33²/(2·0.8·9.81) = 70.79 m
Answer
d = 70.79 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 9.064 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 8·9.81 = 78.48 N
mg·sin θ = 20.31 N
μ·mg·cos θ = 22.74 N
Work–energy
½mv² = (90 − 43.05)·7 = 328.6 J
v = √(2·328.6/8) = 9.064 m/s
Answer
v = 9.064 m/s
9.Momentum & collisions
Answer: v′2 = 16 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 1.5)/(4 + 1.5)·11 = 5 m/s
v′2 = 2·4/(4 + 1.5)·11 = 16 m/s
Answer
v′2 = 16 m/s
10.Momentum & collisions
Answer: Favg = 2800 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.35·(10 + 30) = 14 N·s
Average force
Favg = J/Δt = 14/0.005 = 2800 N
Answer
Favg = 2800 N
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·4.5 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: F = 58.27 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2.25·3 = 58.27 kN
Answer
F = 58.27 kN
13.Continuity & Bernoulli
Answer: p2 = 248.1 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 40 + 273.15 = 313.1 K
TL = -10 + 273.15 = 263.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 5.5·313.1/263.1 = 6.545 kW
Answer
Q̇H = 6.545 kW
Power input: Ẇ = 1.045 kW.
18.Heat engines & refrigerators
Answer: Q̇L = 414.5 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
T0 = 27 + 273.15 = 300.1 K
TL = -5 + 273.15 = 268.1 K
Engine work
η = 1 − 300.1/1023 = 0.7066
Ẇ = 0.7066·70 = 49.46 kW
Heat removed by the refrigerator
COPR = 268.1/(300.1 − 268.1) = 8.38
Q̇L = 8.38·49.46 = 414.5 kW
Answer
Q̇L = 414.5 kW
19.Waves, sound & optics
Answer: β = 96 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity
I = P/(4πr²) = 0.003979 W/m²
Level
β = 10·log₁₀(0.003979/10⁻¹²) = 96 dB
Answer
β = 96 dB
20.Waves, sound & optics
Answer: di = 21.43 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.