Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −6.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 12 m/s from the edge of a roof 15 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 12 m/sh₀ = 15 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 5 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 5 kgθ = 30°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 6 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 6 kgm2 = 4.5 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 22 m/s and 50° above the horizontal towards a wall 19 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 22 m/sθ = 50°x = 19 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 21 m/s and 60° above the horizontal from the top of a 55 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 21 m/sθ = 60°h = 55 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 2 kg block slides 14 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 2 kgθ = 45°μ = 0.3d = 14 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg cart is released from rest at a height of 18 m on a smooth track that leads into a vertical circular loop of radius 4 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 0.5 kgh = 18 mR = 4 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 0.5 kg glider moving at 4 m/s makes a perfectly elastic head-on collision with a 2 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 0.5 kgm2 = 2 kgv1 = 4 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.45 kg ball hits a wall at 11 m/s and bounces straight back at 20 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.45 kgvin = 11 m/svout = 20 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 1 mb = 2 mρ = 1260 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows at 28 L/s through a horizontal pipe that narrows from 150 mm to 75 mm. The pressure in the narrow section is 140 kPa. Ignoring losses, find the pressure p1 in the wide section.
A hose with an inner diameter of 32 mm siphons water from an open tank. The highest point C of the hose is 3 m above the water surface, and the outlet (open to the air) is 3 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 32 mmzC = +3 mz2 = −3 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
A tank of 5 L contains 160 g of Ar at 85 °C. Treat it as an ideal gas and find the pressure P.
A heat engine works between a hot reservoir at 725 °C and a cold reservoir at 25 °C. Find the highest possible thermal efficiency ηmax.
TH = 725 °CTL = 25 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 650 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 10 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 650 °CTL = 10 °C
Tm = °C
19.Waves, sound & opticsMedium
A pipe closed at one end must have its harmonic number 3 at 643 Hz. The speed of sound is 343 m/s. Find the length L of the pipe.
v = 343 m/sn = 3f3 = 643 Hz
L = m
20.Waves, sound & opticsHard
Light of wavelength 405 nm falls at right angles on a grating with 300 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 300 mm⁻¹λ = 405 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: s = 69.23 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·6.5) = 69.23 m
Answer
s = 69.23 m
2.Kinematics
Answer: t = 3.357 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−15 = 12·t − ½·9.81·t²
4.905·t² − 12·t − 15 = 0
Solve the quadratic
Only the positive root is physical.
t = (12 + √(12² + 2·9.81·15))/9.81 = 3.357 s
Answer
t = 3.357 s
3.Newton’s laws
Answer: a = 2.356 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 22·cos 50° = 14.14 m/s
t = x/vx = 19/14.14 = 1.344 s
Height at that time
y = 16.85·1.344 − ½·9.81·1.344² = 13.79 m
Answer
y = 13.79 m
The ball is still rising at the wall.
6.Projectile motion
Answer: H = 71.86 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 21·sin 60° = 18.19 m/s
Rise above the cliff
Δh = vy²/(2g) = 18.19²/(2·9.81) = 16.86 m
Height above the ground
H = 55 + 16.86 = 71.86 m
Answer
H = 71.86 m
7.Work & energy
Answer: Wf = 58.27 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 19.62·0.7071 = 13.87 N
F = μN = 0.3·13.87 = 4.162 N
Work against friction
Wf = F·d = 4.162·14 = 58.27 J
Answer
Wf = 58.27 J
8.Work & energy
Answer: N = 19.62 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(18 − 8) = 196.2 m²/s²
Forces at the top
m·g = 0.5·9.81 = 4.905 N
N = mv²/R − mg = 0.5·196.2/4 − 4.905 = 19.62 N
Answer
N = 19.62 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′2 = 1.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 2)/(0.5 + 2)·4 = −2.4 m/s
v′2 = 2·0.5/(0.5 + 2)·4 = 1.6 m/s
Answer
v′2 = 1.6 m/s
10.Momentum & collisions
Answer: Favg = 2790 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.45·(20 + 11) = 13.95 N·s
Average force
Favg = J/Δt = 13.95/0.005 = 2790 N
Answer
Favg = 2790 N
11.Hydrostatic force
Answer: F = 156.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.25·3.75 = 156.3 kN
Answer
F = 156.3 kN
12.Hydrostatic force
Answer: ycp = 3.524 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1/2 = 3.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.5·2 = 86.52 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 473.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(400/700)·(473.1/283.1) = 19.1 L
Answer
V2 = 19.1 L
17.Heat engines & refrigerators
Answer: ηmax = 70.13 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 725 + 273.15 = 998.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/998.1 = 70.13 %
Answer
ηmax = 70.13 %
18.Heat engines & refrigerators
Answer: Tm = 238.1 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 10 + 273.15 = 283.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(923.1·283.1) = 511.3 K = 238.1 °C
Answer
Tm = 238.1 °C
19.Waves, sound & optics
Answer: L = 0.4001 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 343/643 = 0.5334 m
Length
L = nλ/4 = 3·0.5334/4 = 0.4001 m
Answer
L = 0.4001 m
20.Waves, sound & optics
Answer: θ1 = 6.979 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …