Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 15 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 15 m/sh₀ = 25 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 5 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 5 kgθ = 30°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 105 N pulls the front 10 kg block; the 1 kg block is towed behind. The coefficient of kinetic friction is 0.2 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 1 kgm2 = 10 kgF = 105 Nμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 18 m/sθ = 70°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 60 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 34 m/sθ = 40°h = 60 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 5 kg block slides 8 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 5 kgθ = 35°μ = 0.3d = 8 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 5 kg block rests on a rough horizontal table (μ = 0.15). A light string runs from it over a smooth pulley at the edge of the table to a hanging 2 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 2 m.
m1 = 5 kgm2 = 2 kgμ = 0.15d = 2 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 3.5 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3.5 kgm2 = 5 kgv1 = 10 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 12 m/s and bounces straight back at 9 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.5 kgvin = 12 m/svout = 9 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 50 mm. The pressure at the inlet is 48 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 9 m. At section 1 the pressure is 290 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 750 °C and a cold reservoir at 40 °C. Find the highest possible thermal efficiency ηmax.
TH = 750 °CTL = 40 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 2 °C outside, delivering 14 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 2 °CQ̇H = 14 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 20 cm in front of a thin converging lens with a focal length of 15 cm. Find the magnification m (negative for an inverted image).
do = 20 cmf = 15 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls at right angles on a grating with 200 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 200 mm⁻¹λ = 532 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: s = 150 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·3) = 150 m
Answer
s = 150 m
2.Kinematics
Answer: hmax = 36.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 15²/(2·9.81) = 11.47 m
Height above the ground
hmax = 25 + 11.47 = 36.47 m
Answer
hmax = 36.47 m
3.Newton’s laws
Answer: a = 3.206 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: x = 21.23 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 70° = 6.156 m/s
vy = v0·sin θ = 18·sin 70° = 16.91 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·16.91/9.81 = 3.448 s
Horizontal distance
x = vx·t = 6.156·3.448 = 21.23 m
Answer
x = 21.23 m
6.Projectile motion
Answer: x = 166 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 40° = 26.05 m/s
vy = v0·sin θ = 34·sin 40° = 21.85 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 60 + 21.85·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (21.85 + √(477.6 + 1177))/9.81 = 6.375 s
Horizontal distance
x = vx·t = 26.05·6.375 = 166 m
Answer
x = 166 m
7.Work & energy
Answer: Wf = 96.43 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.8192 = 40.18 N
F = μN = 0.3·40.18 = 12.05 N
Work against friction
Wf = F·d = 12.05·8 = 96.43 J
Answer
Wf = 96.43 J
8.Work & energy
Answer: v = 2.647 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 19.62·2 = 39.24 J
μ·m₁g·d = 0.15·49.05·2 = 14.71 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 24.53 → v = √(2·24.53/7) = 2.647 m/s
Answer
v = 2.647 m/s
9.Momentum & collisions
Answer: v′2 = 8.235 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 5)/(3.5 + 5)·10 = −1.765 m/s
v′2 = 2·3.5/(3.5 + 5)·10 = 8.235 m/s
Answer
v′2 = 8.235 m/s
10.Momentum & collisions
Answer: Favg = 1050 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(9 + 12) = 10.5 N·s
Average force
Favg = J/Δt = 10.5/0.01 = 1050 N
Answer
Favg = 1050 N
11.Hydrostatic force
Answer: F = 110.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·4.5 = 110.4 kN
Answer
F = 110.4 kN
12.Hydrostatic force
Answer: ycp = 1.4 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1.5/2 = 1.25 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.25·3 = 37.71 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(50/100)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/1023 = 69.39 %
Answer
ηmax = 69.39 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.9487 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 14/14.76 = 0.9487 kW
Answer
Ẇmin = 0.9487 kW
19.Waves, sound & optics
Answer: m = −3
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/15 − 1/20
di = 60 cm
Magnification
m = −di/do = −60/20 = −3
Answer
m = −3
20.Waves, sound & optics
Answer: θ2 = 12.29 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …