Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 8 m/s² until it stops. How long does braking take? Find t.
v₀ = 90 km/ha = −8 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 17 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 17 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
Masses of 7.5 kg and 3.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 7.5 kgm2 = 3.5 kgg = 9.81 m/s²
T = N
4.Newton’s lawsHard
A 3 kg block on a ramp at 40° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 9.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3 kgm2 = 9.5 kgθ = 40°μ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 16 m/sθ = 20°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 31 m/sθ = 50°h = 30 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 14 m along the slope.
θ = 45°μ = 0.15d = 14 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2.5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.3) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2.5 kgh = 3 mL = 5 mμ = 0.3k = 4000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 4 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 4 kgm2 = 0.5 kgv1 = 3 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.25 kg ball hits a wall at 14 m/s and bounces straight back at 12 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.25 kgvin = 14 m/svout = 12 m/sΔt = 50 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 1 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 2.5 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 290 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 200 mm, throat 150 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 350 mm. The discharge coefficient is 0.99. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine receives heat from a source at 450 °C and rejects heat to the surroundings at 10 °C. Its actual thermal efficiency is 37%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 450 °CTL = 10 °Cη = 37%
ηII = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 750 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 30 °C. Both engines produce the same work. Find Tm in °C.
TH = 750 °CTL = 30 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends is 1.5 m long; waves travel on it at 200 m/s. Find the frequency f2 of its harmonic number 2.
v = 200 m/sn = 2L = 1.5 m
f2 = Hz
20.Waves, sound & opticsHard
Light of wavelength 405 nm falls at right angles on a grating with 1200 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 1200 mm⁻¹λ = 405 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: t = 3.125 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 25/8 = 3.125 s
Answer
t = 3.125 s
2.Kinematics
Answer: t = 4.394 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 17·t − ½·9.81·t²
4.905·t² − 17·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (17 + √(17² + 2·9.81·20))/9.81 = 4.394 s
Answer
t = 4.394 s
3.Newton’s laws
Answer: T = 46.82 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (7.5 − 3.5)·9.81/(7.5 + 3.5) = 3.567 m/s²
Tension from the lighter mass
T − m2·g = m2·a → T = 3.5·(9.81 + 3.567) = 46.82 N
Answer
T = 46.82 N
4.Newton’s laws
Answer: a = 5.582 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 93.2 N
m₁·g·sin θ = 18.92 N
μ·m₁·g·cos θ = 4.509 N
Acceleration of the system
a = (93.2 − 18.92 − 4.509)/12.5 = 5.582 m/s²
Answer
a = 5.582 m/s²
5.Projectile motion
Answer: t = 1.116 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 20° = 15.04 m/s
vy = v0·sin θ = 16·sin 20° = 5.472 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·5.472/9.81 = 1.116 s
Answer
t = 1.116 s
6.Projectile motion
Answer: t = 5.881 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 31·cos 50° = 19.93 m/s
vy = v0·sin θ = 31·sin 50° = 23.75 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 23.75·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (23.75 + √(563.9 + 588.6))/9.81 = 5.881 s
Answer
t = 5.881 s
7.Work & energy
Answer: v = 12.85 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·14·(0.7071 − 0.15·0.7071)) = 12.85 m/s
Answer
v = 12.85 m/s
8.Work & energy
Answer: v = 5.425 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(3 − 0.3·5) = 36.79 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·1.5) = 5.425 m/s
Answer
v = 5.425 m/s
9.Momentum & collisions
Answer: v′1 = 2.333 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 0.5)/(4 + 0.5)·3 = 2.333 m/s
v′2 = 2·4/(4 + 0.5)·3 = 5.333 m/s
Answer
v′1 = 2.333 m/s
10.Momentum & collisions
Answer: J = 6.5 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.25·(12 + 14) = 6.5 N·s
Answer
J = 6.5 N·s
11.Hydrostatic force
Answer: F = 29.43 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1/2 = 1.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·2 = 29.43 kN
Answer
F = 29.43 kN
12.Hydrostatic force
Answer: F = 48.56 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2.25·2.5 = 48.56 kN
Answer
F = 48.56 kN
13.Continuity & Bernoulli
Answer: p2 = 288 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.35 = 43262 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(200/450)·(443.1/293.1) = 3.359 L
Answer
V2 = 3.359 L
17.Heat engines & refrigerators
Answer: ηII = 60.81 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 450 + 273.15 = 723.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηCarnot = 1 − 283.1/723.1 = 60.84 %
Second-law efficiency
ηII = η/ηCarnot = 37/60.84 = 60.81 %
Answer
ηII = 60.81 %
18.Heat engines & refrigerators
Answer: Tm = 390 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 30 + 273.15 = 303.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1023 + 303.1)/2 = 663.1 K = 390 °C
Answer
Tm = 390 °C
19.Waves, sound & optics
Answer: f2 = 133.3 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1.5/2 = 1.5 m
Frequency
f = v/λ = 200/1.5 = 133.3 Hz
Answer
f2 = 133.3 Hz
20.Waves, sound & optics
Answer: θ1 = 29.08 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …