Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 8 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −8 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 7 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 7 m/sh₀ = 40 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
An 8 kg block slides down a frictionless slope at 30° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3 kgm2 = 2 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 50° above the horizontal and lands 125 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 50°R = 125 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 30 m/s and 40° above the horizontal from the top of a 5 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 30 m/sθ = 40°h = 5 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 2000 N/m. A 0.1 kg ball is placed on it and the spring is compressed by 6 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.1 kgk = 2000 N/mx = 6 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 2 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.3) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 2 mL = 3 mμ = 0.3k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3 kgm2 = 1 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 1 kg block hanging from light strings 0.9 m long, and stays in it. The strings swing out to a largest angle of 20° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 1 kgL = 0.9 mθ = 20°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a water pipe reads a difference of 37 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 37 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 10 m. At section 1 the pressure is 370 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 1000 kJ of heat from a reservoir at 425 °C and rejects 427 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 425 °CQH = 1000 kJQL = 427 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat engine takes in 2000 kJ of heat from a reservoir at 600 °C, produces 1080 kJ of work and rejects the rest to a reservoir at 15 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 600 °CTL = 15 °CQH = 2000 kJW = 1080 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
Light travels in diamond (n = 2.42) towards a flat boundary with glycerol (n = 1.47). Find the critical angle θc beyond which it is totally reflected.
n1 = 2.42n2 = 1.47
θc = °
20.Waves, sound & opticsHard
Light of wavelength 500 nm passes through a single slit 0.1 mm wide. Find the width w of the central bright maximum on a screen 2 m away (between the first dark fringes on either side).
λ = 500 nma = 0.1 mmL = 2 m
w = mm
3Solutions
1.Kinematics
Answer: s = 39.06 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·8) = 39.06 m
Answer
s = 39.06 m
2.Kinematics
Answer: hmax = 42.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 7²/(2·9.81) = 2.497 m
Height above the ground
hmax = 40 + 2.497 = 42.5 m
Answer
hmax = 42.5 m
3.Newton’s laws
Answer: a = 4.905 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·125/sin 100°) = 35.29 m/s
Answer
v0 = 35.29 m/s
6.Projectile motion
Answer: v = 31.59 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 30·cos 40° = 22.98 m/s
vy0 = 30·sin 40° = 19.28 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(19.28² + 2·9.81·5) = 21.68 m/s
Impact speed
v = √(22.98² + 21.68²) = 31.59 m/s
Answer
v = 31.59 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: h = 3.67 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 6 cm = 0.06 m
½kx² = ½·2000·0.06² = 3.6 J
Height
m·g = 0.1·9.81 = 0.981 N
h = ½kx²/(mg) = 3.6/0.981 = 3.67 m
Answer
h = 3.67 m
8.Work & energy
Answer: x = 29.38 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(2 − 0.3·3) = 21.58 J
Maximum compression
½kx² = 21.58 → x = √(2·21.58/500) = 0.2938 m = 29.38 cm
Answer
x = 29.38 cm
9.Momentum & collisions
Answer: v′2 = 16.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 1)/(3 + 1)·11 = 5.5 m/s
v′2 = 2·3/(3 + 1)·11 = 16.5 m/s
Answer
v′2 = 16.5 m/s
10.Momentum & collisions
Answer: v = 87.03 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.9·(1 − cos 20°) = 0.05428 m
Speed after impact
V = √(2·9.81·0.05428) = 1.032 m/s
Collision
v = (m + M)·V/m = 1.012·1.032/0.012 = 87.03 m/s
Answer
v = 87.03 m/s
11.Hydrostatic force
Answer: F = 202.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·7.5 = 202.3 kN
Answer
F = 202.3 kN
12.Hydrostatic force
Answer: F = 74.16 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·1.5·4 = 74.16 kN
Answer
F = 74.16 kN
13.Continuity & Bernoulli
Answer: v = 8.602 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·37000/1000) = 8.602 m/s
Answer
v = 8.602 m/s
14.Continuity & Bernoulli
Answer: p2 = 271.6 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 483.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(350/550)·(483.1/288.1) = 2.134 L
Answer
V2 = 2.134 L
17.Heat engines & refrigerators
Answer: TL = 24.96 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 425 + 273.15 = 698.1 K
Reversible heat ratio
TL = TH·QL/QH = 698.1·427/1000 = 298.1 K = 24.96 °C
Answer
TL = 24.96 °C
18.Heat engines & refrigerators
Answer: Sgen = 0.9022 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 2000 − 1080 = 920 kJ
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 15 + 273.15 = 288.1 K
Entropy changes of the reservoirs
ΔSH = −2000/873.1 = −2.291 kJ/K
ΔSL = 920/288.1 = 3.193 kJ/K
Sgen = 3.193 − 2.291 = 0.9022 kJ/K
Answer
Sgen = 0.9022 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: θc = 37.4 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.47/2.42 = 0.6074
Critical angle
θc = arcsin(0.6074) = 37.4°
Answer
θc = 37.4°
20.Waves, sound & optics
Answer: w = 20 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …