Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 72 km/h sees an obstacle. Her reaction time is 1.1 s, after which the car brakes with a constant deceleration of 6.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 72 km/htr = 1.1 sa = −6.5 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 8 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 8 m/sh₀ = 40 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 20 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 20 kgθ = 25°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 12 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 12 m/sθ = 20°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 34 m/sθ = 50°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 21 m/s and 20° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 21 m/sθ = 20°h = 50 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A 2 kg block slides 18 m down a slope at 15° to the horizontal, with a coefficient of kinetic friction of 0.1. Find the work Wf done against friction.
m = 2 kgθ = 15°μ = 0.1d = 18 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 1 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.15) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 1 kgh = 2 mL = 3 mμ = 0.15k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2 kg glider moving at 4 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 4.5 kgv1 = 4 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 1300 kg car travelling east at 24 m/s collides with a 1000 kg car travelling north at 14 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1300 kgv1 = 24 m/s (E)m2 = 1000 kgv2 = 14 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 200 mm and a throat diameter of 150 mm. The pressure at the inlet is 16 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 9 m. At section 1 the pressure is 340 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 675 °C and a cold reservoir at 25 °C. It takes in 1400 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 675 °CTL = 25 °CQH = 1400 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -20 °C in a kitchen at 35 °C, removing heat from the cold space at 4 kW. Find the minimum power input Ẇmin.
TH = 35 °CTL = -20 °CQ̇L = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with crown glass (n = 1.50) for every angle of incidence above 35°. Find the refractive index n1 of the block.
θc = 35°n2 = 1.50
n1 =
20.Waves, sound & opticsHard
A sensor at rest sends ultrasound of 25 kHz towards a car that approaches at 25 m/s and mixes the echo with the emitted signal. Find the beat frequency fb (speed of sound 343 m/s).
f = 25 kHzu = 25 m/sv = 343 m/s
fb = Hz
3Solutions
1.Kinematics
Answer: d = 52.77 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Reaction distance
d1 = v₀·tr = 20·1.1 = 22 m
Braking distance
d2 = v₀²/(2a) = 20²/(2·6.5) = 30.77 m
Total
d = 22 + 30.77 = 52.77 m
Answer
d = 52.77 m
2.Kinematics
Answer: t = 3.785 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−40 = 8·t − ½·9.81·t²
4.905·t² − 8·t − 40 = 0
Solve the quadratic
Only the positive root is physical.
t = (8 + √(8² + 2·9.81·40))/9.81 = 3.785 s
Answer
t = 3.785 s
3.Newton’s laws
Answer: a = 2.812 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 20° + 0.1·cos 20°) = 4.277 m/s²
Distance
d = v₀²/(2a) = 12²/(2·4.277) = 16.83 m
Answer
d = 16.83 m
5.Projectile motion
Answer: x = 116 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 50° = 21.85 m/s
vy = v0·sin θ = 34·sin 50° = 26.05 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·26.05/9.81 = 5.31 s
Horizontal distance
x = vx·t = 21.85·5.31 = 116 m
Answer
x = 116 m
6.Projectile motion
Answer: α = 58.45 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 21·cos 20° = 19.73 m/s
vy0 = 21·sin 20° = 7.182 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(7.182² + 2·9.81·50) = 32.13 m/s
Impact angle
tan α = vy/vx = 32.13/19.73 → α = 58.45°
Answer
α = 58.45°
7.Work & energy
Answer: Wf = 34.11 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 19.62·0.9659 = 18.95 N
F = μN = 0.1·18.95 = 1.895 N
Work against friction
Wf = F·d = 1.895·18 = 34.11 J
Answer
Wf = 34.11 J
8.Work & energy
Answer: x = 14.24 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(2 − 0.15·3) = 15.21 J
Maximum compression
½kx² = 15.21 → x = √(2·15.21/1500) = 0.1424 m = 14.24 cm
Answer
x = 14.24 cm
9.Momentum & collisions
Answer: v′1 = −1.538 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 4.5)/(2 + 4.5)·4 = −1.538 m/s
v′2 = 2·2/(2 + 4.5)·4 = 2.462 m/s
Answer
v′1 = −1.538 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: θ = 24.17 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1300·24 = 31200 kg·m/s
py = 1000·14 = 14000 kg·m/s
Direction
tan θ = py/px = 0.4487 → θ = 24.17°
Answer
θ = 24.17°
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·4.5 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: F = 14.71 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·1.5 = 14.71 kN
Answer
F = 14.71 kN
13.Continuity & Bernoulli
Answer: Q = 120.9 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/200)² = 0.5625·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 323.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(150/250)·(323.1/293.1) = 3.307 L
Answer
V2 = 3.307 L
17.Heat engines & refrigerators
Answer: Wmax = 959.8 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 675 + 273.15 = 948.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/948.1 = 68.55 %
Maximum work
Wmax = ηmax·QH = 0.6855·1400 = 959.8 kJ
Answer
Wmax = 959.8 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.869 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4/4.603 = 0.869 kW
Answer
Ẇmin = 0.869 kW
19.Waves, sound & optics
Answer: n1 = 2.615
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.50/0.5736 = 2.615
Answer
n1 = 2.615
20.Waves, sound & optics
Answer: fb = 3931 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.