Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 260 km/h to take off and the usable runway is 2100 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 260 km/hs = 2100 m
a = m/s²
2.KinematicsHard
Ball A is dropped from rest from a height of 10 m. At the same instant ball B is thrown straight up from the ground directly below at 21 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 10 mv0B = 21 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 19 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 19 kgθ = 40°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 6.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 6.5 kgm2 = 5 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 22 m/s and must land 40 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 22 m/sR = 40 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is thrown from ground level at 19 m/s and 55° above the horizontal. It lands on the flat roof of a building 3 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 19 m/sθ = 55°hroof = 3 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 1000 kg car drives up a 3° slope at a constant 72 km/h. Air resistance and rolling resistance together amount to 250 N. Find the power P the wheels must deliver, in kW.
An 8 kg block rests on a rough horizontal table (μ = 0.3). A light string runs from it over a smooth pulley at the edge of the table to a hanging 3 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 3 m.
m1 = 8 kgm2 = 3 kgμ = 0.3d = 3 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 15 g bullet is fired horizontally into a 2.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 7 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 2.5 kgh = 7 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 14 m/s and bounces straight back at 10 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.5 kgvin = 14 m/svout = 10 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 25 mm. The water level is kept 2 m above the orifice and the discharge coefficient is 0.61. Find the flow rate Q. Use g = 9.81 m/s².
d = 25 mmh = 2 mCd = 0.61g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A horizontal venturi meter (inlet 80 mm, throat 40 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 260 mm. The discharge coefficient is 0.97. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible refrigerator keeps a cold room at -25 °C by removing 2.5 kW of heat, and rejects heat to the surroundings at 30 °C. Find the rate Q̇H at which it rejects heat.
TL = -25 °CTH = 30 °CQ̇L = 2.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump delivers 4 kW of heat to a heating system at 35 °C, taking heat from a source at 5 °C. Its actual COP is 40% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 35 °CTL = 5 °CηII = 40%Q̇H = 4 kW
Ẇ = kW
19.Waves, sound & opticsMedium
An object stands 50 cm in front of a thin converging lens with a focal length of 8 cm. Find the magnification m (negative for an inverted image).
do = 50 cmf = 8 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 486 nm falls at right angles on a grating with 800 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 800 mm⁻¹λ = 486 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: a = 1.242 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 260/3.6 = 72.22 m/s
Acceleration
a = v²/(2s) = 72.22²/(2·2100) = 1.242 m/s²
Answer
a = 1.242 m/s²
2.Kinematics
Answer: t = 0.4762 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
10 − ½g·t² = 21·t − ½g·t² → t = 10/21 = 0.4762 s
Answer
t = 0.4762 s
3.Newton’s laws
Answer: a = 4.803 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·40/22² = 0.8107
Angle
2θ = 54.17° → θ = 27.08°
Answer
θ = 27.08°
The other solution is 90° − θ = 62.92°.
6.Projectile motion
Answer: x = 32.33 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 10.9 m/s, vy = 15.56 m/s
Time to land on the roof
Larger root: the ball is descending.
3 = 15.56·t − 4.905·t²
t = (15.56 + √(15.56² − 2·9.81·3))/9.81 = 2.967 s
Horizontal distance
x = vx·t = 10.9·2.967 = 32.33 m
Answer
x = 32.33 m
7.Work & energy
Answer: P = 15.27 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1000·9.81 = 9810 N
mg·sin θ = 9810·sin 3° = 513.4 N
F = 513.4 + 250 = 763.4 N
Power
v = 72/3.6 = 20 m/s
P = F·v = 763.4·20 = 15268 W = 15.27 kW
Answer
P = 15.27 kW
8.Work & energy
Answer: v = 1.792 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 29.43·3 = 88.29 J
μ·m₁g·d = 0.3·78.48·3 = 70.63 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 17.66 → v = √(2·17.66/11) = 1.792 m/s
Answer
v = 1.792 m/s
9.Momentum & collisions
Answer: v = 196.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.07) = 1.172 m/s
Collision
m·v = (m + M)·V → v = (0.015 + 2.5)·1.172/0.015 = 196.5 m/s
Answer
v = 196.5 m/s
10.Momentum & collisions
Answer: Favg = 2400 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(10 + 14) = 12 N·s
Average force
Favg = J/Δt = 12/0.005 = 2400 N
Answer
Favg = 2400 N
11.Hydrostatic force
Answer: F = 95.65 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·3 = 95.65 kN
Answer
F = 95.65 kN
12.Hydrostatic force
Answer: F = 90.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3·3 = 90.5 kN
Answer
F = 90.5 kN
13.Continuity & Bernoulli
Answer: Q = 1.876 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·2) = 6.264 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.26 = 32138 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 30 + 273.15 = 303.1 K
TL = -25 + 273.15 = 248.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 2.5·303.1/248.1 = 3.054 kW
Answer
Q̇H = 3.054 kW
Power input: Ẇ = 0.5541 kW.
18.Heat engines & refrigerators
Answer: Ẇ = 0.9736 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 35 + 273.15 = 308.1 K
TL = 5 + 273.15 = 278.1 K
Carnot and actual COP
COPmax = 308.1/(308.1 − 278.1) = 10.27
COP = 0.4·10.27 = 4.109
Power input
Ẇ = Q̇H/COP = 4/4.109 = 0.9736 kW
Answer
Ẇ = 0.9736 kW
19.Waves, sound & optics
Answer: m = −0.1905
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/8 − 1/50
di = 9.524 cm
Magnification
m = −di/do = −9.524/50 = −0.1905
Answer
m = −0.1905
20.Waves, sound & optics
Answer: θ1 = 22.88 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …