Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 120 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
v₀ = 120 km/ha = −6.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 16 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 16 m/sh₀ = 40 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 5.5 m/s and comes to rest after 10 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 5.5 m/sd = 10 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 2.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 2.5 kgm2 = 3 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 18 m/sθ = 45°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 23 m/sθ = 60°h = 35 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 5 kg block slides 2 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 5 kgθ = 25°μ = 0.35d = 2 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 20 kg block starts from rest at the bottom of a 30° slope and is pulled up the slope by a constant force of 185 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 5 m up the slope.
An 8 g bullet is fired horizontally into a 3 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 16 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 3 kgh = 16 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.25 kg ball hits a wall at 19 m/s and bounces straight back at 8 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
m = 0.25 kgvin = 19 m/svout = 8 m/sΔt = 25 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 1 mb = 3 mρ = 1260 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 130 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 100 mm while rising 5 m. At section 1 the pressure is 320 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at -5 °C by removing 6.5 kW of heat, and rejects heat to the surroundings at 35 °C. Find the rate Q̇H at which it rejects heat.
TL = -5 °CTH = 35 °CQ̇L = 6.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -10 °C in a kitchen at 32 °C, removing heat from the cold space at 1 kW. Find the highest possible coefficient of performance COPmax.
TH = 32 °CTL = -10 °CQ̇L = 1 kW
COPmax =
19.Waves, sound & opticsMedium
One machine gives a sound level of 70 dB at a certain point. Find the level β at that point when 4 identical machines run at the same time (incoherent sources).
β1 = 70 dBn = 4
β = dB
20.Waves, sound & opticsHard
Two thin lenses share an axis, 25 cm apart: lens 1 with f₁ = 12 cm and lens 2 with f₂ = 10 cm. An object stands 40 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 12 cmf2 = 10 cms = 25 cmdo = 40 cm
di2 = cm
3Solutions
1.Kinematics
Answer: s = 85.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 33.33²/(2·6.5) = 85.47 m
Answer
s = 85.47 m
2.Kinematics
Answer: t = 4.92 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−40 = 16·t − ½·9.81·t²
4.905·t² − 16·t − 40 = 0
Solve the quadratic
Only the positive root is physical.
t = (16 + √(16² + 2·9.81·40))/9.81 = 4.92 s
Answer
t = 4.92 s
3.Newton’s laws
Answer: μ = 0.1542
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 5.5²/(2·10) = 1.512 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.512/9.81 = 0.1542
Answer
μ = 0.1542
4.Newton’s laws
Answer: a = 4.236 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 45° = 12.73 m/s
vy = v0·sin θ = 18·sin 45° = 12.73 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·12.73/9.81 = 2.595 s
Answer
t = 2.595 s
6.Projectile motion
Answer: x = 61.94 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 23·cos 60° = 11.5 m/s
vy = v0·sin θ = 23·sin 60° = 19.92 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 19.92·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (19.92 + √(396.7 + 686.7))/9.81 = 5.386 s
Horizontal distance
x = vx·t = 11.5·5.386 = 61.94 m
Answer
x = 61.94 m
7.Work & energy
Answer: Wf = 31.12 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.9063 = 44.45 N
F = μN = 0.35·44.45 = 15.56 N
Work against friction
Wf = F·d = 15.56·2 = 31.12 J
Answer
Wf = 31.12 J
8.Work & energy
Answer: v = 5.912 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 20·9.81 = 196.2 N
mg·sin θ = 98.1 N
μ·mg·cos θ = 16.99 N
Work–energy
½mv² = (185 − 115.1)·5 = 349.5 J
v = √(2·349.5/20) = 5.912 m/s
Answer
v = 5.912 m/s
9.Momentum & collisions
Answer: v = 666.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.16) = 1.772 m/s
Collision
m·v = (m + M)·V → v = (0.008 + 3)·1.772/0.008 = 666.2 m/s
Answer
v = 666.2 m/s
10.Momentum & collisions
Answer: Favg = 270 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.25·(8 + 19) = 6.75 N·s
Average force
Favg = J/Δt = 6.75/0.025 = 270 N
Answer
Favg = 270 N
11.Hydrostatic force
Answer: F = 147.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·6 = 147.2 kN
Answer
F = 147.2 kN
12.Hydrostatic force
Answer: F = 129.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1/2 = 3.5 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.5·3 = 129.8 kN
Answer
F = 129.8 kN
13.Continuity & Bernoulli
Answer: p2 = 128.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(200/600)·(443.1/293.1) = 2.519 L
Answer
V2 = 2.519 L
17.Heat engines & refrigerators
Answer: Q̇H = 7.47 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 35 + 273.15 = 308.1 K
TL = -5 + 273.15 = 268.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 6.5·308.1/268.1 = 7.47 kW
Answer
Q̇H = 7.47 kW
Power input: Ẇ = 0.9696 kW.
18.Heat engines & refrigerators
Answer: COPmax = 6.265
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Total intensity
I = 4·I₁
Level
β = 70 + 10·log₁₀(4) = 76.02 dB
Answer
β = 76.02 dB
20.Waves, sound & optics
Answer: di2 = −36.67 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.