Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. Find the braking distance s.
v₀ = 100 km/ha = −7.5 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 3.6 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 3.6 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 10 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 10 kgθ = 25°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1 kgm2 = 5 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 28 m/sθ = 30°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 55 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 24 m/sθ = 55°h = 55 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 80 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.8. Find the stopping distance d.
v = 80 km/hμ = 0.8g = 9.81 m/s²
d = m
8.Work & energyHard
A 2 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.1) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2 kgh = 4 mL = 2 mμ = 0.1k = 4000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 15 kg projectile moving horizontally at 26 m/s explodes into two fragments that move along the same line. The 4 kg fragment continues forwards at 60 m/s. Find the velocity v′2 of the 11 kg fragment (positive in the original direction).
M = 15 kgu = 26 m/sm1 = 4 kgv′1 = 60 m/sm2 = 11 kg
v′2 = m/s
10.Momentum & collisionsHard
An 8 g bullet is fired horizontally into a 2 kg block hanging from light strings 0.7 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 2 kgL = 0.7 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 2 mb = 1 mρ = 1260 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows at 33 L/s through a horizontal pipe that narrows from 100 mm to 75 mm. The pressure in the narrow section is 60 kPa. Ignoring losses, find the pressure p1 in the wide section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 75 mm and a gauge pressure of 100 kPa. The nozzle exit diameter is 40 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 1200 kJ of heat from a reservoir at 500 °C and rejects 509 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 500 °CQH = 1200 kJQL = 509 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 35 °C, removing heat from the cold space at 2 kW. Find the minimum power input Ẇmin.
TH = 35 °CTL = -25 °CQ̇L = 2 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.75 m long; waves travel on it at 150 m/s. Find the frequency f4 of its harmonic number 4.
v = 150 m/sn = 4L = 0.75 m
f4 = Hz
20.Waves, sound & opticsHard
Light of wavelength 650 nm falls on two slits 0.1 mm apart. The screen is 2.5 m away. Find the spacing Δy between neighbouring bright fringes.
λ = 650 nmd = 0.1 mmL = 2.5 m
Δy = mm
3Solutions
1.Kinematics
Answer: s = 51.44 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 27.78²/(2·7.5) = 51.44 m
Answer
s = 51.44 m
2.Kinematics
Answer: d = 57.76 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(3.6 − t₁)
4.905·t₁² + 343·t₁ − 1235 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1235))/(2·4.905) = 3.432 s
Depth
d = ½·9.81·3.432² = 57.76 m
Answer
d = 57.76 m
3.Newton’s laws
Answer: a = 1.479 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 30° = 24.25 m/s
vy = v0·sin θ = 28·sin 30° = 14 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·14/9.81 = 2.854 s
Answer
t = 2.854 s
6.Projectile motion
Answer: t = 5.907 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 55° = 13.77 m/s
vy = v0·sin θ = 24·sin 55° = 19.66 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 55 + 19.66·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (19.66 + √(386.5 + 1079))/9.81 = 5.907 s
Answer
t = 5.907 s
7.Work & energy
Answer: d = 31.46 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 80/3.6 = 22.22 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 22.22²/(2·0.8·9.81) = 31.46 m
Answer
d = 31.46 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 8.635 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(4 − 0.1·2) = 74.56 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.8) = 8.635 m/s
Answer
v = 8.635 m/s
9.Momentum & collisions
Answer: v′2 = 13.64 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 15·26 = 390 kg·m/s
Momentum after
390 = 4·60 + 11·v′2
v′2 = (390 − 240)/11 = 13.64 m/s
Answer
v′2 = 13.64 m/s
10.Momentum & collisions
Answer: v = 171.7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.7·(1 − cos 15°) = 0.02385 m
Speed after impact
V = √(2·9.81·0.02385) = 0.6841 m/s
Collision
v = (m + M)·V/m = 2.008·0.6841/0.008 = 171.7 m/s
Answer
v = 171.7 m/s
11.Hydrostatic force
Answer: F = 36.79 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1/2 = 2.5 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·1.5 = 36.79 kN
Answer
F = 36.79 kN
12.Hydrostatic force
Answer: F = 98.88 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·4·2 = 98.88 kN
Answer
F = 98.88 kN
13.Continuity & Bernoulli
Answer: p1 = 79.07 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 40/75 = 0.5333
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·100000/(1000·0.9191)) = 14.75 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 14.75²/(2·9.81) = 11.09 m
Answer
H = 11.09 m
15.Ideal gas law
Answer: P = 6227 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 180/4.003 = 44.97 mol
T = 60 + 273.15 = 333.1 K
Pressure
P = nRT/V = 44.97·8.314·333.1/0.02 = 6227 kPa
Answer
P = 6227 kPa
16.Ideal gas law
Answer: ρ = 0.2716 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 170 + 273.15 = 443.1 K
Density
ρ = 250·4.003/(8.314·443.1) = 0.2716 kg/m³
Answer
ρ = 0.2716 kg/m³
17.Heat engines & refrigerators
Answer: TL = 54.79 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 500 + 273.15 = 773.1 K
Reversible heat ratio
TL = TH·QL/QH = 773.1·509/1200 = 327.9 K = 54.79 °C
Answer
TL = 54.79 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.4836 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 2/4.136 = 0.4836 kW
Answer
Ẇmin = 0.4836 kW
19.Waves, sound & optics
Answer: f4 = 400 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.75/4 = 0.375 m
Frequency
f = v/λ = 150/0.375 = 400 Hz
Answer
f4 = 400 Hz
20.Waves, sound & optics
Answer: Δy = 16.25 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …