Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 45 km/ha = −4.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 20 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 20 m/sh₀ = 20 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 25 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 90 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 25 kgF = 90 Nθ = 35°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4 kg block on a ramp at 20° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 4 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 4 kgm2 = 4 kgθ = 20°μ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 32 m/s and 50° above the horizontal towards a wall 62 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 32 m/sθ = 50°x = 62 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 20° above horizontal from the top of a 55 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 28 m/sθ = 20°h = 55 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.1. Find its speed v after it has slid 11 m along the slope.
θ = 35°μ = 0.1d = 11 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg block is released from rest at height 1.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.15) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 1.5 mL = 2 mμ = 0.15k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1.5 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 1.5 kgm2 = 3.5 kgv1 = 10 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 12 m/s and bounces straight back at 4 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.6 kgvin = 12 m/svout = 4 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a water pipe reads a difference of 37 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 37 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
A horizontal venturi meter (inlet 150 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 220 mm. The discharge coefficient is 0.99. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 350 °C and a cold reservoir at 25 °C. It takes in 700 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 350 °CTL = 25 °CQH = 700 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is -10 °C outside, delivering 4 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = -10 °CQ̇H = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 1.5 m long. The speed of sound is 343 m/s. Find the frequency f1 of its fundamental (first harmonic).
v = 343 m/sn = 1L = 1.5 m
f1 = Hz
20.Waves, sound & opticsHard
A parking sensor at rest sends ultrasound of 40 kHz towards a car that approaches at 30 m/s. Find the frequency f″ of the echo received back at the sensor (speed of sound 343 m/s).
f = 40 kHzu = 30 m/sv = 343 m/s
f″ = Hz
3Solutions
1.Kinematics
Answer: t = 2.778 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 12.5/4.5 = 2.778 s
Answer
t = 2.778 s
2.Kinematics
Answer: hmax = 40.39 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 20²/(2·9.81) = 20.39 m
Height above the ground
hmax = 20 + 20.39 = 40.39 m
Answer
hmax = 40.39 m
3.Newton’s laws
Answer: a = 1.4 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 245.3 − 90·sin 35° = 193.6 N
Horizontal forces
m·a = F·cos θ − μ·N = 73.72 − 38.73
a = 35/25 = 1.4 m/s²
Answer
a = 1.4 m/s²
4.Newton’s laws
Answer: a = 2.306 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 39.24 N
m₁·g·sin θ = 13.42 N
μ·m₁·g·cos θ = 7.375 N
Acceleration of the system
a = (39.24 − 13.42 − 7.375)/8 = 2.306 m/s²
Answer
a = 2.306 m/s²
5.Projectile motion
Answer: y = 29.32 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 32·cos 50° = 20.57 m/s
t = x/vx = 62/20.57 = 3.014 s
Height at that time
y = 24.51·3.014 − ½·9.81·3.014² = 29.32 m
Answer
y = 29.32 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 117.5 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 20° = 26.31 m/s
vy = v0·sin θ = 28·sin 20° = 9.577 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 55 + 9.577·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9.577 + √(91.71 + 1079))/9.81 = 4.464 s
Horizontal distance
x = vx·t = 26.31·4.464 = 117.5 m
Answer
x = 117.5 m
7.Work & energy
Answer: v = 10.3 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·11·(0.5736 − 0.1·0.8192)) = 10.3 m/s
Answer
v = 10.3 m/s
8.Work & energy
Answer: x = 17.72 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(1.5 − 0.15·2) = 23.54 J
Maximum compression
½kx² = 23.54 → x = √(2·23.54/1500) = 0.1772 m = 17.72 cm
Answer
x = 17.72 cm
9.Momentum & collisions
Answer: v′2 = 6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 3.5)/(1.5 + 3.5)·10 = −4 m/s
v′2 = 2·1.5/(1.5 + 3.5)·10 = 6 m/s
Answer
v′2 = 6 m/s
10.Momentum & collisions
Answer: Favg = 480 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(4 + 12) = 9.6 N·s
Average force
Favg = J/Δt = 9.6/0.02 = 480 N
Answer
Favg = 480 N
11.Hydrostatic force
Answer: F = 60.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·2.25 = 60.7 kN
Answer
F = 60.7 kN
12.Hydrostatic force
Answer: F = 202.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·7.5 = 202.3 kN
Answer
F = 202.3 kN
13.Continuity & Bernoulli
Answer: v = 8.602 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·37000/1000) = 8.602 m/s
Answer
v = 8.602 m/s
14.Continuity & Bernoulli
Answer: Q = 64.01 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.22 = 27193 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 523.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(150/250)·(523.1/313.1) = 2.005 L
Answer
V2 = 2.005 L
17.Heat engines & refrigerators
Answer: Wmax = 365.1 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 350 + 273.15 = 623.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/623.1 = 52.15 %
Maximum work
Wmax = ηmax·QH = 0.5215·700 = 365.1 kJ
Answer
Wmax = 365.1 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.4216 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 4/9.489 = 0.4216 kW
Answer
Ẇmin = 0.4216 kW
19.Waves, sound & optics
Answer: f1 = 57.17 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·1.5/1 = 6 m
Frequency
f = v/λ = 343/6 = 57.17 Hz
Answer
f1 = 57.17 Hz
20.Waves, sound & optics
Answer: f″ = 47668 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.