Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 100 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 15 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 15 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 14 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 14 kgθ = 25°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3.5 kgm2 = 3.5 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 75° above the horizontal and lands 100 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 75°R = 100 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is thrown from ground level at 35 m/s and 70° above the horizontal. It lands on the flat roof of a building 25 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 35 m/sθ = 70°hroof = 25 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.2. Find its speed v after it has slid 17 m along the slope.
θ = 30°μ = 0.2d = 17 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 0.5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.3) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 3 mL = 2 mμ = 0.3k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
An 18 kg projectile moving horizontally at 10 m/s explodes into two fragments that move along the same line. The 9 kg fragment continues forwards at 27 m/s. Find the velocity v′2 of the 9 kg fragment (positive in the original direction).
M = 18 kgu = 10 m/sm1 = 9 kgv′1 = 27 m/sm2 = 9 kg
v′2 = m/s
10.Momentum & collisionsHard
A 10 g bullet is fired horizontally into a 4 kg block hanging from light strings 0.8 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 4 kgL = 0.8 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure at the inlet is 23 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A hose with an inner diameter of 50 mm siphons water from an open tank. The highest point C of the hose is 2 m above the water surface, and the outlet (open to the air) is 3.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A reversible (Carnot) heat engine takes in 1200 kJ of heat from a reservoir at 375 °C and rejects 552 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 375 °CQH = 1200 kJQL = 552 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -20 °C in a kitchen at 28 °C, removing heat from the cold space at 5 kW. Find the minimum power input Ẇmin.
TH = 28 °CTL = -20 °CQ̇L = 5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A small source sends sound equally in all directions. The level is 80 dB at 5 m from it. Find the level β2 at 15 m, ignoring absorption and reflections.
β1 = 80 dBr1 = 5 mr2 = 15 m
β2 = dB
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.48 and a cladding with n₂ = 1.43. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.48n2 = 1.43n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: s = 128.6 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 27.78²/(2·3) = 128.6 m
Answer
s = 128.6 m
2.Kinematics
Answer: t = 4.607 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 15·t − ½·9.81·t²
4.905·t² − 15·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (15 + √(15² + 2·9.81·35))/9.81 = 4.607 s
Answer
t = 4.607 s
3.Newton’s laws
Answer: a = 2.812 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·100/sin 150°) = 44.29 m/s
Answer
v0 = 44.29 m/s
6.Projectile motion
Answer: x = 69.8 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 11.97 m/s, vy = 32.89 m/s
Time to land on the roof
Larger root: the ball is descending.
25 = 32.89·t − 4.905·t²
t = (32.89 + √(32.89² − 2·9.81·25))/9.81 = 5.831 s
Horizontal distance
x = vx·t = 11.97·5.831 = 69.8 m
Answer
x = 69.8 m
7.Work & energy
Answer: v = 10.44 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·17·(0.5 − 0.2·0.866)) = 10.44 m/s
Answer
v = 10.44 m/s
8.Work & energy
Answer: x = 6.862 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(3 − 0.3·2) = 11.77 J
Maximum compression
½kx² = 11.77 → x = √(2·11.77/5000) = 0.06862 m = 6.862 cm
Answer
x = 6.862 cm
9.Momentum & collisions
Answer: v′2 = −7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 18·10 = 180 kg·m/s
Momentum after
180 = 9·27 + 9·v′2
v′2 = (180 − 243)/9 = −7 m/s
Answer
v′2 = −7 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: v = 581.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.8·(1 − cos 30°) = 0.1072 m
Speed after impact
V = √(2·9.81·0.1072) = 1.45 m/s
Collision
v = (m + M)·V/m = 4.01·1.45/0.01 = 581.5 m/s
Answer
v = 581.5 m/s
11.Hydrostatic force
Answer: F = 49.05 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2/2 = 2.5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·2 = 49.05 kN
Answer
F = 49.05 kN
12.Hydrostatic force
Answer: F = 64.38 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·3.75 = 64.38 kN
Answer
F = 64.38 kN
13.Continuity & Bernoulli
Answer: Q = 123.8 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/300)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: P = 173.6 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 140/44.01 = 3.181 mol
T = 55 + 273.15 = 328.1 K
Pressure
P = nRT/V = 3.181·8.314·328.1/0.05 = 173.6 kPa
Answer
P = 173.6 kPa
16.Ideal gas law
Answer: ρ = 2.606 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 50 + 273.15 = 323.1 K
Density
ρ = 250·28.01/(8.314·323.1) = 2.606 kg/m³
Answer
ρ = 2.606 kg/m³
17.Heat engines & refrigerators
Answer: TL = 25 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 375 + 273.15 = 648.1 K
Reversible heat ratio
TL = TH·QL/QH = 648.1·552/1200 = 298.1 K = 25 °C
Answer
TL = 25 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.9481 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 5/5.274 = 0.9481 kW
Answer
Ẇmin = 0.9481 kW
19.Waves, sound & optics
Answer: β2 = 70.46 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity ratio
I₂/I₁ = (5/15)² = 0.1111
New level
β₂ = 80 + 10·log₁₀(0.1111) = 70.46 dB
Answer
β2 = 70.46 dB
Every doubling of the distance lowers the level by about 6 dB.
20.Waves, sound & optics
Answer: θa = 22.42 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.