Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 54 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 54 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 11 m/sh₀ = 40 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 20 kg box is pushed up a ramp at 40° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the pushing force F.
m = 20 kgθ = 40°μ = 0.3g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 5.5 kg block on a ramp at 25° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 8.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.15. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 18 m/sθ = 40°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 24 m/sθ = 40°h = 45 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 500 N/m. A 0.2 kg ball is placed on it and the spring is compressed by 6 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.2 kgk = 500 N/mx = 6 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A spring of stiffness 2000 N/m at the bottom of a 40° slope is compressed by 5 cm against a 0.5 kg block and released. The coefficient of kinetic friction between block and slope is 0.3. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 0.5 kg glider moving at 6 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 0.5 kgm2 = 5 kgv1 = 6 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 29 m/s and bounces straight back at 17 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 29 m/svout = 17 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 50 mm. The pressure at the inlet is 20 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 6 m. At section 1 the pressure is 110 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 650 °C and a cold reservoir at 20 °C. Find the highest possible thermal efficiency ηmax.
TH = 650 °CTL = 20 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 4000 kJ of heat from a reservoir at 900 °C, produces 2400 kJ of work and rejects the rest to a reservoir at 25 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 900 °CTL = 25 °CQH = 4000 kJW = 2400 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
Light travels in diamond (n = 2.42) towards a flat boundary with ethanol (n = 1.36). Find the critical angle θc beyond which it is totally reflected.
n1 = 2.42n2 = 1.36
θc = °
20.Waves, sound & opticsHard
A diffraction grating has 500 lines per millimetre. Light of wavelength 656 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 500 mm⁻¹λ = 656 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 37.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 54/3.6 = 15 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 15²/(2·3) = 37.5 m
Answer
s = 37.5 m
2.Kinematics
Answer: t = 4.189 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−40 = 11·t − ½·9.81·t²
4.905·t² − 11·t − 40 = 0
Solve the quadratic
Only the positive root is physical.
t = (11 + √(11² + 2·9.81·40))/9.81 = 4.189 s
Answer
t = 4.189 s
3.Newton’s laws
Answer: F = 171.2 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 126.1 + 45.09 = 171.2 N
Answer
F = 171.2 N
4.Newton’s laws
Answer: T = 51.06 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 83.39 N
m₁·g·sin θ = 22.8 N
μ·m₁·g·cos θ = 7.335 N
Acceleration of the system
a = (83.39 − 22.8 − 7.335)/14 = 3.803 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 8.5·(9.81 − 3.803) = 51.06 N
Answer
T = 51.06 N
5.Projectile motion
Answer: x = 32.53 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 40° = 13.79 m/s
vy = v0·sin θ = 18·sin 40° = 11.57 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·11.57/9.81 = 2.359 s
Horizontal distance
x = vx·t = 13.79·2.359 = 32.53 m
Answer
x = 32.53 m
6.Projectile motion
Answer: x = 91.66 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 40° = 18.39 m/s
vy = v0·sin θ = 24·sin 40° = 15.43 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 15.43·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (15.43 + √(238 + 882.9))/9.81 = 4.985 s
Horizontal distance
x = vx·t = 18.39·4.985 = 91.66 m
Answer
x = 91.66 m
7.Work & energy
Answer: h = 0.4587 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 6 cm = 0.06 m
½kx² = ½·500·0.06² = 0.9 J
Height
m·g = 0.2·9.81 = 1.962 N
h = ½kx²/(mg) = 0.9/1.962 = 0.4587 m
Answer
h = 0.4587 m
8.Work & energy
Answer: d = 0.5841 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 5 cm = 0.05 m
½kx² = ½·2000·0.05² = 2.5 J
Energy balance along the slope
m·g = 0.5·9.81 = 4.905 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 2.5/(4.905·(0.6428 + 0.3·0.766)) = 0.5841 m
Answer
d = 0.5841 m
9.Momentum & collisions
Answer: v′2 = 1.091 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 5)/(0.5 + 5)·6 = −4.909 m/s
v′2 = 2·0.5/(0.5 + 5)·6 = 1.091 m/s
Answer
v′2 = 1.091 m/s
10.Momentum & collisions
Answer: Favg = 632.5 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(17 + 29) = 25.3 N·s
Average force
Favg = J/Δt = 25.3/0.04 = 632.5 N
Answer
Favg = 632.5 N
11.Hydrostatic force
Answer: F = 103 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·3 = 103 kN
Answer
F = 103 kN
12.Hydrostatic force
Answer: F = 132 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·5.25·2.5 = 132 kN
Answer
F = 132 kN
13.Continuity & Bernoulli
Answer: Q = 12.83 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(50/100)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 293.1/923.1 = 68.24 %
Answer
ηmax = 68.24 %
18.Heat engines & refrigerators
Answer: Sgen = 1.957 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 4000 − 2400 = 1600 kJ
Absolute temperatures
TH = 900 + 273.15 = 1173 K
TL = 25 + 273.15 = 298.1 K
Entropy changes of the reservoirs
ΔSH = −4000/1173 = −3.41 kJ/K
ΔSL = 1600/298.1 = 5.366 kJ/K
Sgen = 5.366 − 3.41 = 1.957 kJ/K
Answer
Sgen = 1.957 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: θc = 34.19 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.36/2.42 = 0.562
Critical angle
θc = arcsin(0.562) = 34.19°
Answer
θc = 34.19°
20.Waves, sound & optics
Answer: mmax = 3
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …