Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 7 m/s² until it stops. Find the braking distance s.
v₀ = 100 km/ha = −7 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 13 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 13 m/sh₀ = 25 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 10 kg box is pushed up a ramp at 40° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the pushing force F.
m = 10 kgθ = 40°μ = 0.25g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 6 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 6 kgm2 = 3 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 26 m/sθ = 35°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 13 m/s and 25° above the horizontal from the top of a 20 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 13 m/sθ = 25°h = 20 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A 4 kg block slides 13 m down a slope at 40° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 4 kgθ = 40°μ = 0.3d = 13 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 4 kg block rests on a rough horizontal table (μ = 0.4). A light string runs from it over a smooth pulley at the edge of the table to a hanging 2 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1.5 m.
m1 = 4 kgm2 = 2 kgμ = 0.4d = 1.5 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 600 kg car moving at 9 m/s runs into a stationary 1000 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 600 kgv1 = 9 m/sm2 = 1000 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 2 kg block hanging from light strings 0.7 m long, and stays in it. The strings swing out to a largest angle of 35° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 2 kgL = 0.7 mθ = 35°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows at 28 L/s through a horizontal pipe that narrows from 200 mm to 100 mm. The pressure in the narrow section is 180 kPa. Ignoring losses, find the pressure p1 in the wide section.
Water flows up through a pipe that narrows from 150 mm to 100 mm while rising 6 m. At section 1 the pressure is 300 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 4900 kJ of heat from a reservoir at 550 °C and rejects 1805 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 550 °CQH = 4900 kJQL = 1805 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 32 °C, removing heat from the cold space at 2.5 kW. Find the minimum power input Ẇmin.
TH = 32 °CTL = -25 °CQ̇L = 2.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A source of 800 Hz moving at 20 m/s and an observer moving at 20 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 800 Hzv = 343 m/svs = 20 m/svo = 20 m/s
f′ = Hz
20.Waves, sound & opticsHard
A grating with 200 lines per millimetre shows the order-1 maximum of a spectral line at 4.6° from the straight-through direction. Find the wavelength λ of the line.
N = 200 mm⁻¹θ1 = 4.6°m = 1
λ = nm
3Solutions
1.Kinematics
Answer: s = 55.11 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 27.78²/(2·7) = 55.11 m
Answer
s = 55.11 m
2.Kinematics
Answer: hmax = 33.61 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 13²/(2·9.81) = 8.614 m
Height above the ground
hmax = 25 + 8.614 = 33.61 m
Answer
hmax = 33.61 m
3.Newton’s laws
Answer: F = 81.84 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 63.06 + 18.79 = 81.84 N
Answer
F = 81.84 N
4.Newton’s laws
Answer: a = 1.308 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 26·cos 35° = 21.3 m/s
vy = v0·sin θ = 26·sin 35° = 14.91 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·14.91/9.81 = 3.04 s
Horizontal distance
x = vx·t = 21.3·3.04 = 64.75 m
Answer
x = 64.75 m
6.Projectile motion
Answer: v = 23.69 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 13·cos 25° = 11.78 m/s
vy0 = 13·sin 25° = 5.494 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(5.494² + 2·9.81·20) = 20.56 m/s
Impact speed
v = √(11.78² + 20.56²) = 23.69 m/s
Answer
v = 23.69 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: Wf = 117.2 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 39.24·0.766 = 30.06 N
F = μN = 0.3·30.06 = 9.018 N
Work against friction
Wf = F·d = 9.018·13 = 117.2 J
Answer
Wf = 117.2 J
8.Work & energy
Answer: v = 1.401 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 19.62·1.5 = 29.43 J
μ·m₁g·d = 0.4·39.24·1.5 = 23.54 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 5.886 → v = √(2·5.886/6) = 1.401 m/s
Answer
v = 1.401 m/s
9.Momentum & collisions
Answer: ΔK = 15188 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 600·9/1600 = 3.375 m/s
Kinetic energy before and after
Kbefore = ½·600·9² = 24300 J
Kafter = ½·1600·3.375² = 9113 J
Energy lost
ΔK = 24300 − 9113 = 15188 J
Answer
ΔK = 15188 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v = 264.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.7·(1 − cos 35°) = 0.1266 m
Speed after impact
V = √(2·9.81·0.1266) = 1.576 m/s
Collision
v = (m + M)·V/m = 2.012·1.576/0.012 = 264.2 m/s
Answer
v = 264.2 m/s
11.Hydrostatic force
Answer: F = 103 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·3 = 103 kN
Answer
F = 103 kN
12.Hydrostatic force
Answer: F = 101.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.25·4.5 = 101.8 kN
Answer
F = 101.8 kN
13.Continuity & Bernoulli
Answer: p1 = 186 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 550 + 273.15 = 823.1 K
Reversible heat ratio
TL = TH·QL/QH = 823.1·1805/4900 = 303.2 K = 30.07 °C
Answer
TL = 30.07 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5742 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 2.5/4.354 = 0.5742 kW
Answer
Ẇmin = 0.5742 kW
19.Waves, sound & optics
Answer: f′ = 899.1 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …