Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 260 km/h to take off and the usable runway is 1700 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 260 km/hs = 1700 m
a = m/s²
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 4.5 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 4.5 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 3 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 3 kgθ = 25°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 11.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 11.5 m/sθ = 30°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 26 m/s and 70° above the horizontal towards a wall 9 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 26 m/sθ = 70°x = 9 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 15 m/sθ = 15°h = 30 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 16 m along the slope.
θ = 40°μ = 0.15d = 16 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.15) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 3 mL = 5 mμ = 0.15k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 2000 kg car moving at 14 m/s runs into a stationary 1900 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 2000 kgv1 = 14 m/sm2 = 1900 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 24 m/s and bounces straight back at 16 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.5 kgvin = 24 m/svout = 16 m/sΔt = 10 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 80 mm and a throat diameter of 40 mm. The pressure at the inlet is 44 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 6 m. At section 1 the pressure is 350 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 550 °C and a cold reservoir at 25 °C. Find the highest possible thermal efficiency ηmax.
TH = 550 °CTL = 25 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 5000 kJ of heat from a reservoir at 600 °C, produces 2300 kJ of work and rejects the rest to a reservoir at 25 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 600 °CTL = 25 °CQH = 5000 kJW = 2300 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with air (n = 1.00) for every angle of incidence above 40°. Find the refractive index n1 of the block.
θc = 40°n2 = 1.00
n1 =
20.Waves, sound & opticsHard
Light of wavelength 656 nm falls at right angles on a grating with 500 lines per millimetre. Find the angle θ3 of the order-3 maximum.
N = 500 mm⁻¹λ = 656 nmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: a = 1.534 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 260/3.6 = 72.22 m/s
Acceleration
a = v²/(2s) = 72.22²/(2·1700) = 1.534 m/s²
Answer
a = 1.534 m/s²
2.Kinematics
Answer: d = 88.29 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(4.5 − t₁)
4.905·t₁² + 343·t₁ − 1544 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1544))/(2·4.905) = 4.243 s
Depth
d = ½·9.81·4.243² = 88.29 m
Answer
d = 88.29 m
3.Newton’s laws
Answer: a = 2.812 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.15·cos 30°) = 6.179 m/s²
Distance
d = v₀²/(2a) = 11.5²/(2·6.179) = 10.7 m
Answer
d = 10.7 m
5.Projectile motion
Answer: y = 19.7 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 26·cos 70° = 8.893 m/s
t = x/vx = 9/8.893 = 1.012 s
Height at that time
y = 24.43·1.012 − ½·9.81·1.012² = 19.7 m
Answer
y = 19.7 m
The ball is still rising at the wall.
6.Projectile motion
Answer: x = 42.02 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 15·cos 15° = 14.49 m/s
vy = v0·sin θ = 15·sin 15° = 3.882 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 3.882·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (3.882 + √(15.07 + 588.6))/9.81 = 2.9 s
Horizontal distance
x = vx·t = 14.49·2.9 = 42.02 m
Answer
x = 42.02 m
7.Work & energy
Answer: v = 12.87 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·16·(0.6428 − 0.15·0.766)) = 12.87 m/s
Answer
v = 12.87 m/s
8.Work & energy
Answer: x = 66.44 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(3 − 0.15·5) = 110.4 J
Maximum compression
½kx² = 110.4 → x = √(2·110.4/500) = 0.6644 m = 66.44 cm
Answer
x = 66.44 cm
9.Momentum & collisions
Answer: ΔK/K = 48.72 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 2000·14/3900 = 7.179 m/s
Kinetic energy before and after
Kbefore = ½·2000·14² = 196000 J
Kafter = ½·3900·7.179² = 100513 J
Fraction lost
ΔK/K = 95487/196000 = 48.72 %
Answer
ΔK/K = 48.72 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 20 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(16 + 24) = 20 N·s
Answer
J = 20 N·s
11.Hydrostatic force
Answer: F = 58.86 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·2 = 58.86 kN
Answer
F = 58.86 kN
12.Hydrostatic force
Answer: F = 38.63 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1.5/2 = 1.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·2.25 = 38.63 kN
Answer
F = 38.63 kN
13.Continuity & Bernoulli
Answer: Q = 12.17 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(40/80)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 523.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(200/550)·(523.1/303.1) = 6.275 L
Answer
V2 = 6.275 L
17.Heat engines & refrigerators
Answer: ηmax = 63.78 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/823.1 = 63.78 %
Answer
ηmax = 63.78 %
18.Heat engines & refrigerators
Answer: Sgen = 3.329 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 5000 − 2300 = 2700 kJ
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 25 + 273.15 = 298.1 K
Entropy changes of the reservoirs
ΔSH = −5000/873.1 = −5.726 kJ/K
ΔSL = 2700/298.1 = 9.056 kJ/K
Sgen = 9.056 − 5.726 = 3.329 kJ/K
Answer
Sgen = 3.329 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: n1 = 1.556
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.00/0.6428 = 1.556
Answer
n1 = 1.556
20.Waves, sound & optics
Answer: θ3 = 79.74 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …