Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 60 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. Find the braking distance s.
v₀ = 60 km/ha = −3.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 6 m/s from the edge of a roof 5 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 6 m/sh₀ = 5 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 3.5 m/s and comes to rest after 1.6 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 3.5 m/sd = 1.6 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 3 kg block on a ramp at 30° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 6 kg mass. The hanging mass moves down. The ramp is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3 kgm2 = 6 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 34 m/sθ = 40°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 15 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 27 m/sθ = 60°h = 15 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 5 kg block slides 2 m down a slope at 30° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 5 kgθ = 30°μ = 0.15d = 2 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A spring of stiffness 500 N/m at the bottom of a 25° slope is compressed by 20 cm against a 3 kg block and released. The coefficient of kinetic friction between block and slope is 0.15. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 4.5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4.5 kgm2 = 4 kgv1 = 9 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.15 kg ball hits a wall at 21 m/s and bounces straight back at 20 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.15 kgvin = 21 m/svout = 20 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a water pipe reads a difference of 9 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 9 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 4 m. At section 1 the pressure is 240 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 675 °C and a cold reservoir at 25 °C. It takes in 4000 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 675 °CTL = 25 °CQH = 4000 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 25 °C, removing heat from the cold space at 0.5 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = -18 °CQ̇L = 0.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 4 cm in front of a thin diverging lens with a focal length of 8 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 4 cmf = −8 cm
di = cm
20.Waves, sound & opticsHard
A diffraction grating has 1200 lines per millimetre. Light of wavelength 532 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 1200 mm⁻¹λ = 532 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 39.68 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 16.67²/(2·3.5) = 39.68 m
Answer
s = 39.68 m
2.Kinematics
Answer: hmax = 6.835 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 6²/(2·9.81) = 1.835 m
Height above the ground
hmax = 5 + 1.835 = 6.835 m
Answer
hmax = 6.835 m
3.Newton’s laws
Answer: μ = 0.3902
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 3.5²/(2·1.6) = 3.828 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 3.828/9.81 = 0.3902
Answer
μ = 0.3902
4.Newton’s laws
Answer: a = 4.905 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 58.86 N
m₁·g·sin θ = 14.71 N
μ·m₁·g·cos θ = 0 N
Acceleration of the system
a = (58.86 − 14.71 − 0)/9 = 4.905 m/s²
Answer
a = 4.905 m/s²
5.Projectile motion
Answer: t = 4.456 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 40° = 26.05 m/s
vy = v0·sin θ = 34·sin 40° = 21.85 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·21.85/9.81 = 4.456 s
Answer
t = 4.456 s
6.Projectile motion
Answer: t = 5.34 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 27·cos 60° = 13.5 m/s
vy = v0·sin θ = 27·sin 60° = 23.38 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 15 + 23.38·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (23.38 + √(546.7 + 294.3))/9.81 = 5.34 s
Answer
t = 5.34 s
7.Work & energy
Answer: Wf = 12.74 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.866 = 42.48 N
F = μN = 0.15·42.48 = 6.372 N
Work against friction
Wf = F·d = 6.372·2 = 12.74 J
Answer
Wf = 12.74 J
8.Work & energy
Answer: d = 0.6083 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·500·0.2² = 10 J
Energy balance along the slope
m·g = 3·9.81 = 29.43 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 10/(29.43·(0.4226 + 0.15·0.9063)) = 0.6083 m
Answer
d = 0.6083 m
9.Momentum & collisions
Answer: v′2 = 9.529 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4.5 − 4)/(4.5 + 4)·9 = 0.5294 m/s
v′2 = 2·4.5/(4.5 + 4)·9 = 9.529 m/s
Answer
v′2 = 9.529 m/s
10.Momentum & collisions
Answer: Favg = 615 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.15·(20 + 21) = 6.15 N·s
Average force
Favg = J/Δt = 6.15/0.01 = 615 N
Answer
Favg = 615 N
11.Hydrostatic force
Answer: F = 39.24 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1/2 = 2 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·2 = 39.24 kN
Answer
F = 39.24 kN
12.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Answer
F = 88.29 kN
13.Continuity & Bernoulli
Answer: v = 4.243 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·9000/1000) = 4.243 m/s
Answer
v = 4.243 m/s
14.Continuity & Bernoulli
Answer: p2 = 183.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 675 + 273.15 = 948.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/948.1 = 68.55 %
Maximum work
Wmax = ηmax·QH = 0.6855·4000 = 2742 kJ
Answer
Wmax = 2742 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.08426 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 0.5/5.934 = 0.08426 kW
Answer
Ẇmin = 0.08426 kW
19.Waves, sound & optics
Answer: di = −2.667 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−8) − 1/4
di = −2.667 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −2.667 cm
20.Waves, sound & optics
Answer: mmax = 1
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …