Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 50 km/h sees an obstacle. Her reaction time is 1.1 s, after which the car brakes with a constant deceleration of 5.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 50 km/htr = 1.1 sa = −5.5 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 13 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 13 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 2.5 m/s and comes to rest after 1.3 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 2.5 m/sd = 1.3 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 10.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 10.5 m/sθ = 30°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 34 m/s and 30° above the horizontal towards a wall 31 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 34 m/sθ = 30°x = 31 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 18 m/sθ = 30°h = 40 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.25. Find its speed v after it has slid 3 m along the slope.
θ = 20°μ = 0.25d = 3 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.25) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 4.5 mL = 2 mμ = 0.25k = 2000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 5 g bullet is fired horizontally into a 2.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 23 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 2.5 kgh = 23 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.45 kg ball hits a wall at 20 m/s and bounces straight back at 8 m/s. The contact lasts 40 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.45 kgvin = 20 m/svout = 8 m/sΔt = 40 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 25 mm. The water level is kept 2 m above the orifice and the discharge coefficient is 0.65. Find the flow rate Q. Use g = 9.81 m/s².
d = 25 mmh = 2 mCd = 0.65g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 25 mm while rising 4 m. At section 1 the pressure is 300 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 5 °C by removing 10 kW of heat, and rejects heat to the surroundings at 35 °C. Find the rate Q̇H at which it rejects heat.
TL = 5 °CTH = 35 °CQ̇L = 10 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 35 °C, removing heat from the cold space at 2 kW. Find the highest possible coefficient of performance COPmax.
TH = 35 °CTL = -18 °CQ̇L = 2 kW
COPmax =
19.Waves, sound & opticsMedium
A small loudspeaker radiates 0.1 W of sound power equally in all directions. Find the sound intensity level β at 1 m.
P = 0.1 Wr = 1 mI0 = 10⁻¹² W/m²
β = dB
20.Waves, sound & opticsHard
Light of wavelength 656 nm falls at right angles on a grating with 1200 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 1200 mm⁻¹λ = 656 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: d = 32.81 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Reaction distance
d1 = v₀·tr = 13.89·1.1 = 15.28 m
Braking distance
d2 = v₀²/(2a) = 13.89²/(2·5.5) = 17.54 m
Total
d = 15.28 + 17.54 = 32.81 m
Answer
d = 32.81 m
2.Kinematics
Answer: t = 3.74 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 13·t − ½·9.81·t²
4.905·t² − 13·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (13 + √(13² + 2·9.81·20))/9.81 = 3.74 s
Answer
t = 3.74 s
3.Newton’s laws
Answer: μ = 0.245
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 2.5²/(2·1.3) = 2.404 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 2.404/9.81 = 0.245
Answer
μ = 0.245
4.Newton’s laws
Answer: d = 8.921 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.15·cos 30°) = 6.179 m/s²
Distance
d = v₀²/(2a) = 10.5²/(2·6.179) = 8.921 m
Answer
d = 8.921 m
5.Projectile motion
Answer: y = 12.46 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 34·cos 30° = 29.44 m/s
t = x/vx = 31/29.44 = 1.053 s
Height at that time
y = 17·1.053 − ½·9.81·1.053² = 12.46 m
Answer
y = 12.46 m
The ball is still rising at the wall.
6.Projectile motion
Answer: t = 3.917 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 30° = 15.59 m/s
vy = v0·sin θ = 18·sin 30° = 9 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 9·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9 + √(81 + 784.8))/9.81 = 3.917 s
Answer
t = 3.917 s
7.Work & energy
Answer: v = 2.511 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·3·(0.342 − 0.25·0.9397)) = 2.511 m/s
Answer
v = 2.511 m/s
8.Work & energy
Answer: x = 28.01 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(4.5 − 0.25·2) = 78.48 J
Maximum compression
½kx² = 78.48 → x = √(2·78.48/2000) = 0.2801 m = 28.01 cm
Answer
x = 28.01 cm
9.Momentum & collisions
Answer: v = 1064 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.23) = 2.124 m/s
Collision
m·v = (m + M)·V → v = (0.005 + 2.5)·2.124/0.005 = 1064 m/s
Answer
v = 1064 m/s
10.Momentum & collisions
Answer: J = 12.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.45·(8 + 20) = 12.6 N·s
Answer
J = 12.6 N·s
11.Hydrostatic force
Answer: F = 323.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·6 = 323.7 kN
Answer
F = 323.7 kN
12.Hydrostatic force
Answer: ycp = 3.028 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·1.5 = 44.15 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·2) = 6.264 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 35 + 273.15 = 308.1 K
TL = 5 + 273.15 = 278.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 10·308.1/278.1 = 11.08 kW
Answer
Q̇H = 11.08 kW
Power input: Ẇ = 1.079 kW.
18.Heat engines & refrigerators
Answer: COPmax = 4.814
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity
I = P/(4πr²) = 0.007958 W/m²
Level
β = 10·log₁₀(0.007958/10⁻¹²) = 99.01 dB
Answer
β = 99.01 dB
20.Waves, sound & optics
Answer: θ1 = 51.92 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …