Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 180 km/h to take off and the usable runway is 1600 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 180 km/hs = 1600 m
a = m/s²
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 11 s, then runs at constant speed for 24 s, and finally brakes at 4.5 m/s² until it stops. Find the total travel time t.
a1 = 3 m/s²t1 = 11 st2 = 24 sa3 = −4.5 m/s²
t = s
3.Newton’s lawsMedium
A 16 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 16 kgθ = 25°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1 kgm2 = 5 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 28 m/sθ = 55°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 15 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 15 m/sθ = 50°h = 15 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.25. Find its speed v after it has slid 5 m along the slope.
θ = 20°μ = 0.25d = 5 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 10 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 70 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 9 m up the slope.
A 6 kg projectile moving horizontally at 37 m/s explodes into two fragments that move along the same line. The 4 kg fragment continues forwards at 93 m/s. Find the velocity v′2 of the 2 kg fragment (positive in the original direction).
M = 6 kgu = 37 m/sm1 = 4 kgv′1 = 93 m/sm2 = 2 kg
v′2 = m/s
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 4.5 kg block hanging from light strings 1.5 m long, and stays in it. The strings swing out to a largest angle of 40° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 4.5 kgL = 1.5 mθ = 40°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 150 mm to 40 mm. In the wide section the pressure is 120 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 300 mm, throat 150 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 90 mm. The discharge coefficient is 0.95. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 600 °C and a cold reservoir at 20 °C. Find the highest possible thermal efficiency ηmax.
TH = 600 °CTL = 20 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump delivers 6.5 kW of heat to a heating system at 35 °C, taking heat from a source at 5 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 35 °CTL = 5 °CηII = 35%Q̇H = 6.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A pipe open at both ends is 1.5 m long. The speed of sound is 343 m/s. Find the frequency f4 of its harmonic number 4.
v = 343 m/sn = 4L = 1.5 m
f4 = Hz
20.Waves, sound & opticsHard
A grating with 400 lines per millimetre shows the order-3 maximum of a spectral line at 51.9° from the straight-through direction. Find the wavelength λ of the line.
N = 400 mm⁻¹θ3 = 51.9°m = 3
λ = nm
3Solutions
1.Kinematics
Answer: a = 0.7813 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 180/3.6 = 50 m/s
Acceleration
a = v²/(2s) = 50²/(2·1600) = 0.7813 m/s²
Answer
a = 0.7813 m/s²
2.Kinematics
Answer: t = 42.33 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·11 = 33 m/s
Braking time
t3 = v/a3 = 33/4.5 = 7.333 s
Total time
t = 11 + 24 + 7.333 = 42.33 s
Answer
t = 42.33 s
3.Newton’s laws
Answer: a = 2.368 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 55° = 16.06 m/s
vy = v0·sin θ = 28·sin 55° = 22.94 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·22.94/9.81 = 4.676 s
Answer
t = 4.676 s
6.Projectile motion
Answer: x = 31.59 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 15·cos 50° = 9.642 m/s
vy = v0·sin θ = 15·sin 50° = 11.49 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 15 + 11.49·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (11.49 + √(132 + 294.3))/9.81 = 3.276 s
Horizontal distance
x = vx·t = 9.642·3.276 = 31.59 m
Answer
x = 31.59 m
7.Work & energy
Answer: v = 3.241 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·5·(0.342 − 0.25·0.9397)) = 3.241 m/s
Answer
v = 3.241 m/s
8.Work & energy
Answer: v = 7.001 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 10·9.81 = 98.1 N
mg·sin θ = 33.55 N
μ·mg·cos θ = 9.218 N
Work–energy
½mv² = (70 − 42.77)·9 = 245.1 J
v = √(2·245.1/10) = 7.001 m/s
Answer
v = 7.001 m/s
9.Momentum & collisions
Answer: v′2 = −75 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 6·37 = 222 kg·m/s
Momentum after
222 = 4·93 + 2·v′2
v′2 = (222 − 372)/2 = −75 m/s
Answer
v′2 = −75 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: v = 986.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.5·(1 − cos 40°) = 0.3509 m
Speed after impact
V = √(2·9.81·0.3509) = 2.624 m/s
Collision
v = (m + M)·V/m = 4.512·2.624/0.012 = 986.6 m/s
Answer
v = 986.6 m/s
11.Hydrostatic force
Answer: F = 9.81 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·1 = 9.81 kN
Answer
F = 9.81 kN
12.Hydrostatic force
Answer: F = 12.36 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·1·1 = 12.36 kN
Answer
F = 12.36 kN
13.Continuity & Bernoulli
Answer: p2 = 21.62 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.09 = 11125 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 293.1/873.1 = 66.43 %
Answer
ηmax = 66.43 %
18.Heat engines & refrigerators
Answer: Ẇ = 1.808 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 35 + 273.15 = 308.1 K
TL = 5 + 273.15 = 278.1 K
Carnot and actual COP
COPmax = 308.1/(308.1 − 278.1) = 10.27
COP = 0.35·10.27 = 3.595
Power input
Ẇ = Q̇H/COP = 6.5/3.595 = 1.808 kW
Answer
Ẇ = 1.808 kW
19.Waves, sound & optics
Answer: f4 = 457.3 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1.5/4 = 0.75 m
Frequency
f = v/λ = 343/0.75 = 457.3 Hz
Answer
f4 = 457.3 Hz
20.Waves, sound & optics
Answer: λ = 655.8 nm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …